Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Hose was in contact with bracket for tub causing the hose to wear thru.
Very easy repair. Removed the lower front panel of the washing machine (two screws) with nutdriver.
Removed hose clamp with pliers. Removed hose from machine. Replaced hose and ran thru a full cycle to check for leaks.
No leaks, back in business in under an hour. This time includes going out to garage and gather the two tools needed for the job and cleaning up the water that came out of the hose during the removal process.
First removed all screws with a nutdriver then lifted the body from the base. Removed the two hoses at the pump (be ready for excess water). Removed the 9/16 bolts (4) to drop the motor assy. I also took off the two front balance springs to have easy access. I at this point was able to remove the pulley and put new belt & pump on the motor. Remember to watch carefully to align belt. removing the idler pulley is a no brainer. Took about 45mins. to complete, a no pro job!!
It was so simple I don't think I even need to explain. Couple of screws in and out and done. Saved big money by doing the repair myself...I was surprised how quickly the part arrived. I was able to access from the back of my machine. Did not have to remove the top. Very easy thanks
Part received was correct (5 days ARO). Removed motor assy from unit (left wires connected). Found drive belt was also worn out & obtained a new one locally. Seperated old pump from rusted motor shaft using 2 screwdrivers. Had to use a file to lightly "polish" rust off motor shaft to install new pump. On-line parts diagram helpful in getting belt properly alinged to idler pully. Machine now runs smoothly, dosn't leak and sound like new. Wife happy (me too)!
1. unplug unit 2. remove front access plate 3. disconnect tension spring on drive belt 4. remove 4 motor mount screws 5. disconnect intake and return lines from pump using a pliers to decompress compression rings and sliding lines off. 6. Manipulate motor and loosen drive belt from bottom of tub and let it hang. 7. tilt motor bottom out exposing pump and remove 3 screws using TREX head driver and remove pump. 8. install new pump
simple as removing front panel from washer held on by two screws and the hose was right their. Took a few minutes to disconnect it from the pump and pull it out through the rear, then feed the replacement in and reverse the process. Piece of cake. Thank you.
I found about 2-3 baby socks stuck in the pump and couldnt remove them so I had to replace the part. Unfortunately I found this website AFTER I took the bad pump off. So I ended up removing the lower front panel and then flipping the washer upside down and removing the bottom of the washer and taking the pump off because I couldnt see any other way to get it off. The new pump arrived very quickly and I put it back on and put the bottom panel back on and flipped the washer back right side up. I certainly made it more difficult then it had to be but it was still fairly easy. Now I see all I needed to do was remove the motor to get the pump off. Oh well.
Remove the front of the washer. Remove the pump and motor assembly using the 1/2 inch socket. Remove the pump from the motor and hoses from the pump. Replace the bad idler pulley and place new belt on pulley. Reassemble the pump to the motor and install the assembly back into the washing machine. Reasemble the hoses and put belt on driven pulley for the drum. Reinstall the front cover.
pulley was worn out and would not turn belt was also worn outand had chunks out of it
Laid washer on its side and had to remove the motor,replaced the pulley and belt replaced the motor and put all parts back together washer spins and runs like it did when it was new.we did not need the screw or nut but did not know when ordering parts
checked for unbalanced load. still banging. removed lower front panel by removing 2 screws. then removed front top panel- 2 more screws. turned unit on spin cycle to see what was going on. this is dangerous as many moving parts are exposed, so keep everything clear. banging was the tensioner slamming back and forth. unpluged washer from outlet and felt along the belt to find part of the 'v' shaped balt had come part, leaving a gap in the "v". ordered part.when i got the part, i removed 4 larger bolts that held the motor, pully, and pump. i unplugged the wires for the motor, and removed the belt from the bsket side pulley assembly by slipping it off and under the shaft. i removed the torx screws that held the pump on the motor and removed the belt. PAY ATTENTION to how the belt was in between the pully and pump assembly or you will have to remove and redo it. reassemble the pump over the belt, pully, motor, and put the belt on the drum side pully before bolting it to the washing machine. it is fairly heavy and tight, so you might need help. this was not hard and you do not need to take apart the washer except for the two front panels and the motor assembly. i just pulled the unit away from the wall and tipped it back to access the inside. take your time and pay attention, and make sure it is not plugged into the wall and you should be fine.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
I had to replace the tub,because it cracked when replacing the bearing and seal
I had no problem replacing the triple lip seal and bearing. I cracked the plastic tub, which after 10 years was very britle and cracked in two places ON THE SIDE. To remove the bearing I had to improvise a bearing removal tool using a puller I had on hand and a 1 lb metal coffee can. It worked great! You need to use some type of pulling device to remove the bearing without damaging the tub.