Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11742857
This shaft is made to fit the center of the idler pulley wheel of many clothes dryers. It is less than two inches long, and is made of metal.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
First removed the bottom access panel, then the then pried the top lid open. Then, I could get to the four screws holding the front of the drum in place. Once that was removed, reached underneath drum and disconnected belt from tensioner pulley and motor. Removed the drum and discovered the problem. One of the two drum rollers had completely disintergrated from the shaft, actually "melting" off of its roller shaft. Removed both of the rollers and shafts by putting a flathead screwdriver on the slot of the shaft, and at the same time holding the locknut behind the bracket with a box wrench. I replaced both shafts and rollers and reused the same washers and snaprings. I used a screwdriver and a vice to remove the snap rings off of the old shafts. The best bet is to use a pair of snap ring pliers, which I didn't have. I used some white silicone grease to lube the new rollers up, reinstalled them and replaced the belt. You MUST route the belt around the drum before you install, then connect the belt to the motor underneath and wrap it around the tensioner. While I had everything opened up, I shop-vac"d the inside of my dryer(filthy). I did this before putting anything back together. Also, when re-installing the front dryer panel, make sure the motor inlet and the lint outlet tube form an airtight seal. All in all, this was a fairly strightforward job. The dryer now works great and is as quiet as a mouse.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Ordered parts per recommendation of expert. Removed front of dryer, removed inner panel, replaced drum support roller, idler pulley shaft, and replaced the belt. Put inner front door on and then front of dryer, voila!!! It works just fine.
Unplug the dryer. Remove bottom panel by removing the two retaining nuts. Unplug the motor cable connections. Remove the blower unit. Remove the two screws holding the motor down. Release the belt by slipping it off the tension pulley. Slide the motor out carefully. I had to replace the idler pulley shaft. The pulley had scored the shaft and was digging into it causing the excessive noise. Reinstall the new shaft and pulley. You will need to remove and re-attach the retaining ring. I took the opportunity to then blow out the motor unit. It was filled with lint. I then decided to replace the original belt. You need to unscrew the rear retaining clips and use a putty knife or (I ended up using a small tire tool) to lift and separate the top. I then slide the belt up to the front of the drum. I unscrewed each bolt from the drum and removed the belt at each corner. By doing this it kept the drum aligned with the unit. Then just reverse the process to install the new belt. Re-install the parts in order of removal. Done. Total repair took about 45 minutes. Would have been quicker except I forgot to re-attach the power clip to the motor and had to remove the unit again.Noise is gone, dryer runs like a champ, hopefully for another ten years.
Remove the front of the washer. Remove the pump and motor assembly using the 1/2 inch socket. Remove the pump from the motor and hoses from the pump. Replace the bad idler pulley and place new belt on pulley. Reassemble the pump to the motor and install the assembly back into the washing machine. Reasemble the hoses and put belt on driven pulley for the drum. Reinstall the front cover.
Removed the bottom panel. Removed door to dryer and disconnected the door switch. Removed the top of the dryer. Now I had access to the drum basket of the dryer. Removed the belt and took drum out. The idler was accessible and easy to replace. I replaced the other drum support rollers. These were a bit difficult when it came to removing the clamp pins holding the rollers. Once you get one the other is easy. Reassembly is relatively easy and quick. Dryer no longer squeals, runs nice. I felt really good.
Unplugged dryer removed the front, removed & marked the wires. Removed the drum & drive belt. Removed the snap ring on front of roller with a pgtai awl.Removed the wheel & worn washers, removed the nut on the back of the roller shaft. reppaced it all in reversed proceedure. Other than a few little scrapes on the knuckles it was Quite easy.
removed screws for lower panel, disconnected wires from door switch, removed front door assy, lifted top, removed drum, replaced idler shafts and rollers with fresh lube. reassembled.Sounds like new. really fast shipping, parts easily located on this website. Thanks!!!
Ordered belt first. After taking it apart, it was clear that the bushing in on of the drum supporting roller was bad. As a result, it has also worn out the shaft. I replaced the roller, roller shaft, and the belt. It is running like new now.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.