A210 Maytag Washer - Instructions

Removed the old one installed the new one

Replaced the pump. The front panel screws were rusty. I also replaced the belts at the same time. The repair video told me just what to do. I wouldn't have known about the belt tension otherwise.

Everything basically went as planned. Putting the belts on was a breeze, but I had trouble getting on the screws that anchored the pump in. The pulley didn't allow access for a nut driver or socket, even with a universal, there still wasn't enough clearance. I went back and forth between using a screw driver in the end of a socket and using the socket on the end of a tiny breaker bar. It wasn't bad, just took a little patience. Everything works like a champ now.

Same technique as the PartSelect video, except the result leaked to the outside at the outlet port because the two halves of the mold that made it were slightly misaligned, and there were two steps, one on each side of the fitting. Filed the steps away, and used Evinrude gasket sealant to make sure it wouldn't leak, and it didn't.

My husband did the repair. Since he owned a laundry quite a few years ago, he knew what he was doing. After hooking everything back up, the cold water was coming in hot. When hooking up the hoses, he had hooked the cold into the top intake. After watching the online video, he realized that the plate that was to be installed over the hoses, on the back of the washer, clearly stated "H" on top and "C" on the bottom. So we switched the position of the hoses and everything ran perfectly after that. I would suggest to ANYONE doing this repair, to watch the online video first, before starting, because it is very, very helpful.

Moved washer away from wall. Removed rear panel (4 screws). removed hose bracket (1 screw). use vicegrip to "open" hose spring clamp. Removed old hose, slipped spring hose clamp over new hose. "Opened" spring hose clamp put new hose over washer drain, released vicegrip. Assemble in reverse.

Watched your viedo, pulled the power plug, pulled the washer away from the wall and tilted back to expose the belts. Rolled the old belts off and put the new ones on. Just be sure to put the correct belt on the pump and agitator drive as they are a bit different. Adjusted the pump belt as described in the inclosed instructions. What was strange was the same instructions was enclosed with the aggiator drive belt which appears to not be adjustable. Once adjusted put washer back in normal position, plugged in power and was ready to go. Seems to work fine now, least no complaints from the wife.

Removed washing Machine Cover. Removed old belts and then old pump. Installed New pump and then the new belts. Cleaned and vacuumed inside of washing Machine. Replaced cover. Hooked up hoses and ran the washer. Every thing worked great and water was pumped out of the washing Machine leaving the cloths spun dry and clean. Really easy job to do.

Emptied washing machine tub with a small plastic bowl into a 5 gallon bucket, finihsing up last bit of water by soaking it up with towels. I next removed front panel on washing machine by unscrewing two screws on the bottom front, left and right, to gain access to the pump. Loosened two hose clamps and detached two hoses, catching remining water from washertub. moved washer out from wall about 3 feet and tilted washer back towards wall so I could access the inderneath of washer to lossen three bolts that held pump in place. removed belt from pum to motor and examined fro glaze or wear (none detected) and then removed pum and reversed steps to install new pump, reinstalling belt faily loosly, per instructions. Tried washer to see if ssue resolved and once confirmed, replaced the front panel. Have done multiple washes since then (at least 10) and no further issues. Very economical solution (under $100) and sense of pride with fixing applianmce myself. This web page was very informative and saved me a lot of money and time. Thanks!

I followed the instructions from the video on the site. It went more difficult than the video showed but it was due to the washer. The instructions were very good. The only really difficult step was taking the bearing sleeve off of the transmission shaft. I ended up with a Dremmel tool and cutting it off. It only took 5 minutes, if that long. The washer has run very well since the repair.

Put the parts on as described in your on-line videos. Was never able to get the metal sleeve off the old machine while installing the Mounting Stem/Tub Seal Kit. I didn't want to cut the sleeve for fear that I wouldn't be able to install the new one and ruin the machine. Video needs to address that issue more fully. Chances are that if these parts need replaced, then the sleeve will be as tight as ours - they won't just slide off like the video shows.

I assumed the belts were bad and were slipping on the pulleys. It took about 10 minutes to install the new belts, however the problem was in the washer transmission which was a difficult and expensive repair and after 22 years of fauless operation,

unplug machine, Remove front cover. Lift the top up and back. Take off the plastic spin basket top. Remove the aggitator. Remove the mounting stem nut, set screw, and remove the spin basket. Remove the mounting stem. Unbolt the three tub support brackets. take off the bleach dispenser hose, the pump hose, and the water level sensor. lift out the tub. push out the old seal and bearing. Clean everything and install the new seal. Reinstall the tub including the mounting stem seal. replace the spin basket. replace the plastic top. Hook up all the hoses. Replace the top. Cycle the machine and check for leaks before replacing the front cover.

Had to take the back off to replace valve

I did it per the video on line and was a snap.I don't have issue recomending the web site to my freinds who want to do repairs themselves.