Models > 61004753 > Instructions

61004753 Maytag Refrigerator - Instructions

All installation instructions for 61004753 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 61004753
91-105 of 119
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

the water line broke and the new water line was leaking due to bad connector

  • Customer: Vincent from Brooklyn NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
repair was just like in the video. no surprises

No water for the ice maker

  • Customer: William from Carmel CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
The only part I needed was the Valve assembly. I checked for frost and found none. I took out the Ice Maker and found it was in poor condition but working. I did put in a new one but with the same problem. I finally read the comments from your costumers and found one place that told about a leaky water valve that was letting water drip into the ice maker so slowly it froze and blocked the valve. So I put in a new valve and thawed the pipe and allis well. What made this job so easy was the costumers comments and the best was the one day delivery of the parts. Thank you for all your help.

The ice in the storage tray would melt and stop up the delivery door.

  • Customer: Marcus from Redfield AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Got online typed in Maytag repairs. Watched the repair video. At that point I removed the door assembly (5 screws total) saw the broken door. Ordered the part from Partselect. Part was delivered in 3 days and installation was a very easy process.Thanks for the help.

broken dispenser

  • Customer: Harrison from Darien GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
easy, followed instructions and installed new parts.

Bracket that moves the ice door chute broke allowing the door to fall into the chute

  • Customer: Ken from Cleveland TN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video and followed the instructions ... time to repair was slightly longer than expected due to the fact that my fridge had wood panels requiring removal. Still, the video was terrific since I am a visual type person.Part Select service was amazing ... ordered one day and the part arrived at my door the very next day. Had the same type of service on a previous repair to replace the ice crushing part of the ice maker. What a company!!! Thanks so much.

water would dispense at the door when the ice maker refilled

  • Customer: john from sulphur LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I shut the water valve and bled the pressure off by using the water dispenser. Removed the four screws that hold the cardboard backing on the unit. Unplugged the power cord, loosened the metal water supply fitting. Then I removed all three hose fittings and dried the drips with a towel. I pushed the electrical plugs off with a flat blade screw driver. Removed the bracket attachment screw and pulled the double valve out. The new valves came with a push-lock fitting for the plastic hoses so I pushed them into their sockets. Put the new valve in and replaced the attachment screw. Reattached the water supply line and the electrical connectors. I turned the water on and checked for leaks. replaced the cardboard backing, and plugged the power cord back in.

The flapper door broke

  • Customer: JW from Garner NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the directions from the YouTube video, which were spot on correct! Loved it. No problems. I did have to wind the spring one more turn than it showed on the video, but that was easy to figure out. No problems!

Door Kit Broken

  • Customer: Howard from Fulton TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
I had to buy the ice dispenser solenoid AND door kit just to get the door kit. The little flapper door was all that needed repair. I followed the video and this was so easy.. anyone could do this repair. PartSelect made this small job easy. Many thanks. HBoykin

Icemaker door flap bracket broke

  • Customer: KEVIN from RAMSEY MN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
The home service repair through our utility company checked the refridgerator and then looked for parts. Their conclusion is the part was no longer available and we should "just reach into the icemaker when we want ice until we replace the refridgerator.) The refridgerator is a top of the line model and replacement cost is well over $2,000 so that wasn't a good option. So I checked PartSelect and found the part which I received in 3 days, installed it in a few minutes and we're back in operation!

Ice or Water Dispenser irratic shut-off.

  • Customer: Terrance from Rochester MN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Previewed the videos supplied by PartSelect first. Followed the directions to remove the control panel that contained both the old switch and the old actuator pad. Removed old switch and old actuator pad. Then spent about 45 minutes cleaning lime deposits on wate tube and around ice-maker chute. Our unit was nearly 4 years old. Used a tooth brush, white vinegar, and elbow grease to remove the lime buildup. Then put in new switch and new actuator pad; and reassembled panels back into door. Total time about 75 minutes.

water dispenser was leaking

  • Customer: Robert from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Followed the video exactly. Replaced both valves in less than 1 hour. No more leakage. Very simple!

Ice door broke

  • Customer: Alfred from Woodbury MN
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the instructions that came with the kit.

Flap on ice dispenser was broken

  • Customer: Joan from Bessemer AL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
We put all the new parts in that came with this kit including the Solenoid. It was super easy. I have a home warranty which covered the refrigerator ice maker, however, it would have cost me $75 just to bring out a repairman and then it would have taken up my time to be around when he wanted to come out. Buying this part and doing the job ourself cost me less money AND time.

low water pressure for ice maker and water for drinking

  • Customer: jim from De Soto MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
replacing the electric water valves was not to bad took about 30 minutes but still had low water pressure traced it to the filter housing had good pressure going in but low coming out so I removed the housing and found a rubber washer was restricting the water flow so I removed the washer ,put it back together and it worked fine

ice dispenser door support broke

  • Customer: Frederick from Trenton NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed dispenser unit, replaced solenoid and door support, and reassembled. Repair video on website was extremely helpful. Only needed door support but found it was easier to order and install the entire assembly with the new door. Item number PS2003478
All Instructions for the 61004753
91-105 of 119