57731H9WW General Electric Washer - Instructions

As straightforward as indicated by other customers. Remove the clip, replace the knob, replace the clip. Done

R & R drain hose

The staff at parts Select are one of a kind, my order came before expected. Thanks Parts Select

I checked the motor,it was bad I was pulling to 20 amps too much. The washer was still not working and the motor was bad so I checked the lid switch for continuity. The switch was a magnet type so with the lid down you should have continuity. In other words, a closed circuit. When the lid is opened, you should have a open circuit, Which would show no continuity. An open circuit means a break in the circuit. To change hinge bushings, raise lid, remove the screws on the outside of the lid, remove hinge, remove lid, insert new hinge bushings, place hinge through lid into bushings, and then put the screws back into the lid. If you followed these steps you should be done.

Lay the washer on its side, unscrew three screw to loose the rotor, put the belt and screw the rotor back.

replaced cycle selector knob. received part in less than 24 hrs.

Replaced the knob by removing the old one an installing the new one with plastic clip. Very easy repair. The water pumb was not working. After determining that it was getting electricity, I removed it and took it apart to determine whether or not it was clogged. To my amazement,I found a "quarter" stuck at the bottom. With a little effort, I removed the piece and put the pump back together, reinstalled it to the hoses and the repair was complete. The Part Select site is fantastic. The schmatic drawings and diagosntic information make even very complex repairs possible! Thank you. I am a very happy customer!

Just popped new knob on shaft , took about 1 min.

DISCONNECT POWER----1.- No pump sound when energized but I know it energized as the coil became a magnet. 2.- You need a drain pan to catch the water from the lower tub when the drain hose is disconnected from the pump. 3.- Water pump or channel lock pliers needed to remove the spring clamps on inlet and outlet from pump. 4.- Remove the 2 hold down bolts and the plug in power connection and the pump comes out very easily. 5.- On my pump I found a plastic tie wrap lodged in the pump impeller vanes-- this caused the pump either not to work at all or cause a cavitation effect caused the water in the tub not to drain completely. 6.- Since I had already purchased the new pump I installed the new pump and cleaned the old one to keep as a spare-- probably never going to need it though.7.- On the large diameter drain hose ( pump inlet ) I decided to use a auto hose clamp instead of the original spring clamp because the area to work on this pump is very cramped and getting the original spring clamp back on was very difficult. The hose clamp made it very easy and the seal was just fine. 8.- The new pump functions perfectly- PARTS SELECT delivered a quality OEM product and I am extremely satisfied with their normal delivery which was 2 days because the warehouse was only 150 miles from me.

My washer didn't come with a fabric softener dispenser. I found one on your website and purchased (the part arrived in two days). I popped the top off the agitator, lined up the notches on the fabric softener dispenser with the inside notches on the agitator and pressed down. Voila! Less than 5 minutes, no tools needed.

I pushed out the pin that held the old knob in place with a thin flat head screwdriver. Old knob came right off. Put on the new one and pushed the new pin in with the screwdriver again and it was good to go.

I pulled off the old knob. The retaining clip was left on the shaft and had to be pulled off separately. That was easy. Then the new knob just pressed back on the shaft as easy as could be. And luckily, I chose the exact replacement knob from the pictures available, without knowing the model number of my GE clothes dryer.

watched supplied on-line video

removed and replaced knob by just pulling old one off and pushing new one on.

I was frantically trying to find a cheap washer to replace the one that "broke". Fortunately, my son's roommate is a maintenance technician. He diagnosed the problem immediately. I googled the issue, found the part, ordered it and received delivery of the part in 3 days. It took all of 5 minutes to replace the part and reassemble the washer. Now on to the 15 loads of laundry that have been stacking up!

replace knop