Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replace plastic wheels on refridgerator
I used board levers to do one side at a time.Kinda tricky, but you can hoist up fridge high enough to replace wheels. take your time think it out and be safe . Make sure you use saftey boards to support load to protect yourself==good luck A small mirror may help to see how the rollers alien in the supports.
I determined that the ice maker was not getting any water. There was only one possibilty, the water inlet assembly. I removed the cover on the bottom back side of the fridge, then removed two screws, three water connections by hand, two electrical connections, reversed everything that I had previously done and in about twenty minutes the ice maker had water.
I removed the plastic cover from the top hinge and loosened the screws. The magnet seal kept the door in place so I removed the top hinge and tried to lift the door off the bottom hinge but the water line wouldn't let it go. Since I don't use the water feature, I just cut the water line and lifted the door off. That's when I discovered the hinge pin was actually broken off, not just the cam. I went ahead and replaced the cam kit and put it temporarily back together, got right back on line and ordered the bottom hinge. The service was again very fast and in a couple of days I received the bottom hinge, repeated the whole process again and this time replaced the bottom hinge assembly, put some petrolium jelly on the cam kit and now it works smooth and perfect.
First I removed the knobs, then the plastic cover over the thermostat. Then, I removed the two screws that hold it on. I removed the thermostat, unplugged the electrical leads, and pulled out the old thermostat. I then inserted the new one, hooked up the leads and reassembled.
Part of cam broke off bottom of fridg. door & it quit closing automatically
Took longer to move food from door to inside fridge & take grandkids' artwork off door, & then put it all back than it did to replace cam. 1. Used phillips head to undo 1 screw holding cover over top bracket; lifted off cover. 2. No need to have someone hold door while you remove top bracket; magnets in door gasket will hold it tight to fridge. Used socket to remove 3 screws in top bracket & lifted bracket up off top of door. 3. Door's not heavy. I stood on a sturdy chair to get better leverage. Opened the door enough to break the magnetic seal & llfted it up off bottom bracket. I moved it over just enough to get to the cam, rested the bottom of the door on the floor, & leaned it up against the open front of the fridge to help preserve chilled food. 4. Removed the 1 screw holding in the bad cam to the bottom bracket (uses smaller socket than screws on top bracket). 5. I checked part that goes up inside bottom of door & it was fine, so did not replace it. 6. Trickiest part: putting the door back on. I put a hand mirror on floor by the right corner & facing up so I could see the underpart of the door as I lifted it eased it down on the right place. 7. Closed door, made sure it was straight, replaced top hinge & cover, food, & artwork.
tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok
coupling on water line thru freezer door cut due to moving Refg and having to remove doors.
Snapped the large end of the coupling onto the main line coming from the water source and snapped the other end onto the small line leading to the ice maker. Quick and simple.
I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!
Freezer was not staying cold enugh for ice maker to work. Discovered fan was not working to cool condensor. Fan motor would only run if manually turned.
Unplugged refrigerator. Removed lower back access panels and panel running up the back of refrigerator. Removed and disconnected old fan. Removed old fan motor from mounting bracket. Removed fan blade from old fan motor and placed on new fan motor. Connected new fan motor to power supply. Tested. Reinstalled.
I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.
The icemaker unit comes right off, only 3 screws hold it in place, so it was a breeze replacing it. I probably saved a couple hundred bucks by doing it myself, thanks to the great service at partselect.com.
Shut water off at source, disconnect electrical supply at wall, remove screws retaining cardboard dust cover, and remove cover. Removed water supply line to control valve, remove two screws retaining unit to frame of refrigerator, and gently pull out unit. Remove two water lines, making sure to note where each line was connected to unit. Remove two electrical connectors, making sure to note where each line was connected, remove old valve. Noting where mounting bracket is positioned, remove old mounting bracket from valve, and reinstall bracket on new valve the same way. Coat threads lightly on new valve with vaseline, reinstall valve in reverse order, making sure not to over-tighten water connections. Note, before installing dust cover, reconnect wall power, and turn on water and inspect for leaks, at connections. Tighten leaking connections very slightly until leak stops. Reinstall dust cover, and carefully return refrigerator to it's original location.
Lower RH door hinge was making a snapping noise because door closure cam screw backed out and damaged cam by egg-shaping hole.
Removed door. Removed old cam closure assembly. Noticed that there was almost nothing inside the door for screw to screw into(only styrofoam insulation), which is why original screw backed out. Bad design. Got longer screw at bigger diameter. Pushed high strength glue into hole, on screw threads, and underneath screw head. Assembled. Crossed fingers. About three weeks have passed and so far, so good.