36071 (P1108705W) Litton Refrigerator - Instructions

Ordered replacement icemaker from PartSelect.com. Upon receipt of part installed part as per the online video. All went well. Whirlpool rep. stated that the icemake works well when the freezer temp. is set at 10 degrees or less.It took appreximately 24 hrs.for the icemaker to fill the bucket with fresh ice. It would hace cost approximately $230.00 or more if I had called a Service rep. to do the job. So I elected to do it myself.

well, my problem was the dual water valve. I check the two water valve connectors, one was good ( yellow ) and the other connector (brown) was bad. I tested them both with an ohms meter, of course all power was off. I think when ever there's a problem with not receiving ICE this should be done before replacing the ice-maker for there's a lot of things going on in this area. The Brown Connector releases the water into the ice-tray (that tested Bad with a reading of 257 from ohms meter,and the yellow had a sound from ohms for full contact a good reading. The brown valve was bad.

First My Frig side of the double door unit wasn't closing on its own. Kids don't look, so they walk away...next thing you know the frig warms up and the freezer starts to frost up from running so long...Now it won't shut off.... I checked the hinge and sure enough it was wore down. Now mind you, I ordered a hinge kit first without checking to see what type I needed...don't do that...Less than 15 mins you can take the door off and see which one you need.As soon as I saw which type of hinge set I needed I went and ordered it...returned the other one. It came pretty quick.... 15 mins had that sucker changed and working... But... the door still wouldn't close on its own... Common sense told me the heat from the frosted freezer caused the door and frig walls to swell... Yes I said the heat... When the component in the freezer frosts up it does not keep the frig cool, nor will the freezer stay kool... the frost prevents the cool air from moving around...thus "HEAT".... It took a full 24 hrs for my frig n freezer to get back to normal... and now the door closes just fine... MIND YOU! I had to take the covers off the freezer unit inside, then take a steamer and melt all that frost off of every inch including down the drain... That took me a good 5-6 hours... and what a mess.... but it was worth my time.... because I don't have to replace my second hand Jenn-Air which I could never afford to buy brand new.... Whew....what we have to do to keep things going... $11 bucks worth of parts.... "Super Mom" :o)

Mine was alittle different than the online instructions. 1. I removed the motor. 2. I took the fan off the old motor and cut the wires about 3" back from old motor. 3. Mounted the new fan on bracket and put the fan on the new motor. 4.connected wires that were cut and used wire nuts to connect. 5. Mounted bracket and motor/fan to unit and it works like its brand new. Thank you PartSelect!

followed repair help directions

Watching the video made this dead easy. If I had a newer refrigerator, I suspect it would have taken 10 minutes. Since I have an older 'fridge, I ran into two issues not in the PartSelect video. First - there were no "clips" to slip the icemaker into/out of, the unit was screwed directly into the freezer wall. Kinda hard to see the screws, especially the one in front, but not a big problem. Second - there is a wire-harness clip at the back side of the icemaker, that hooks onto the ledge of the back connector, just under the screw. That clip had slipped, and until I figured that out and reseated it, it made getting to the rear screw wit the nutdriver a serious pain. Other than those two issues, though, the job was exactly as easy as the video makes it look!

Cubes in bin were freezing together due to water leaking from the ice maker assembly. Replacement went easy with bin rails removed.

1. removed bottom screw. 2. pinched sides of rear connection to disconnected ice maker (noted red wire on top in cabinet rear). 3. bump out old unit taping to release tab on bottom. 4. disconnect wire from icemaker and remove wire holder with philips screwdriver.ew ice maker. 4. reattach harness to new ice make and replace clip. 6 reattach l bracket to bottom of ice maker. 7. detach shut off wire from old ice maker and replace on the new maker. 8. place back into position in freezer compartment. 9. reattach water delivery tube 10. connect wire to rear of cabinet. If motor drive still good on old maker scavenge before throwing away bad parts.

empty frezzer take door off unplug wires going to ice maker unscrew/bolt icemaker replace door take motor cover off ice maker remove screws on motor replace ice cup and put every thing back together

Took out socket, replaced new bulb in new socket and plugged in. Easy!

took the door off the hinges laided flat and withcordless drill and socket took the gasket off and replaced it with new one

I unplugged the refrigerator. Then removed the ice tray. Then removed the screw holding the ice maker secure. I had a little difficulty lifting the ice maker off the clips on the side of the refrigerator but was successful. Then unplugged the wire harness from the back of the refrigerator an lifted the unit out. Removed the wiring harness from the old unit and installed it on the new one. Then positioned the new unit so I could plug the harness in the refrigerator and lined up the clips to attach it on the side of the refrigerator, being careful to line up the water distribution tube. Replaced the screw to secure the ice maker and plugged the refrigerator back in and it is working very well. I am very hsappy with the repair

Video was helpful and reading the other responses online was a big help also. Followed all of those instructions. Most difficult part was disconnecting the electrical plug to the ice maker. Need a screwdrive or other pointed object to depress plastic tab. Other than that, things went smoothly. HOWEVER, after turning water back on and plugging in fridge, I thought everthing was perfect...no leaks initially. BUT, came back a few hours later to find no ice cubes in the holding tray, "iceburg" formations and ice dams built up again thoughout the freezer. Water was leaking continuously from the ice maker. Upon further analysis, it appears the electronic mechanism keeps telling the fridge to send water to the ice maker...or, it is sending too much before shutting the water off. The tray is overflowing and that seems to be the problem. I'm back to square one, but with a new ice maker.

Quickly after video

Watched the video on the web site and then followed the instructions. It was very easy to change. After changing it, I filled it with water from a cup to get it started making ice since the video does not address how to do this. It has been working well ever since. If you are handy with tools, you can do this.