Models > 11042822201 > Instructions

11042822201 Kenmore Dishwasher - Instructions

All installation instructions for 11042822201 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 11042822201
136-150 of 158
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

WORN OUT PART

  • Customer: Mark from Albuquerque NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
RepLACE OLD PART

drive belt slipping

  • Customer: John from Anderson SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Old belt and new belt were not exactly the same. did research and deturminded that the new belt was correct. Reomoved the back panel and rolled the old belt off. Pully is designed to allow changing of the belt without taking the pully off. Put new belt on the motor pully ensuring it was in the groves. started belt on the drum pully and turned it untill it was tight. With an open hand I held the belt on the drum pully so it would not slip off and gave the drum a quick turn to jump the belt onto the pully. rotated the system several turns to make sure everything tracked correctly. Replaced the back panel.

would not drain

  • Customer: Thomas from Bunnlevel NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
replaced drain pump.Saved 200$

Water was flowing into the drum when the washer was off.

  • Customer: Bob from Haverhill MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The water inlet vavle was pretty easy to find once I took the top off. The water input hoses connect directly to it and 2 electrical connection per valve. One screw needs to be removed. The only trick is to slide the valve to the left to remove. It is captured by the sheet metal washer housing at the base of the male hose connetion.

F 02 error and the tub would not drain properly. Had some amount of noise when the drain pump was running.

  • Customer: Richard from Lake Jackson TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I unplugged the power and tilted the washer back and removed the kick panel. I then unscrewed the pump trap access and set aside. I used the shop vac to remove the remaing water from the washer to the drain pump, unplugged power to the pump, removed the discharge hose and suction hose. After everything was removed, I removed the pump. Everything I read said to take the pump loose before removing everything, it just worked better for me to take everything loose with the pump secure. Going back together I mounted the new pump, plugged it back in (I did not have to remove anything from the plug to use it on the new pump as the insert indicated), installed the discharge hose and the suction hose. I found it easier to rotate the clamp a bit on the sucttion hose to allow me to use my right hand to depress the clamp to get it back in place. Replaced the kick panel, lowered the washer back in place, plugged it in and ran it through a cycle, worked great.

Washer filling when not in use

  • Customer: KURT from Quakertown PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
removed top cover,disconnected wires to valve,removed valve and hooked up a washer hose to test valve,one side was leaking,valve would not close.replaced with new valve that I received in 2 days,do not buy after market.

My washing machine was not draining

  • Customer: Katherine from Ridge NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the old pump and replaced it with the new one. I am the happiest person on earth right now to have my washing machine working at its best again. Thank you so much.

Won't spin

  • Customer: turbo trucking from mio MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Replaced water pump

Water flow problem resulting in f20 error code

  • Customer: John from Norman OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Unplugged electric cord and turned off water supply. Remove 3 screws @ rear of washer and removed top panel. Removed clamps on hoses and electrical connector to flow meter, removed and replaced with new flow meter. Replaced the top panel, turned on water supply and plugged unit in. Finished in less than 15 minutes. Saved myself several hundred $

The latch was broken so that the front door wouldn't close.

  • Customer: Jennifer from Staunton VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the guy on the video. The only parts that were tough was having the right tools and having enough space to put the new part in. The part was only 70 dollars and I was so proud that I could do it. I am not very handy so if I can do it then anyone can. Plus I saved some money!

Water filling drum when unit was off

  • Customer: Dave from Sammamish, WA WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Removed the top of the washer by removing 3 screws on the back and sliding the top back and up. Removed the power cord and pipes. Next removed a screw holding the valve in place. Labeled the wires and pulled them off. The hard part was moving the locking tube ring further back on the tube before pulling the inlet tube off the valve. Reattach the black inlet tube and locking ring. I had to keep working it before it was in the right place. Some have mentioned that the hole didn't line up when they installed the valve. It turns out that there is a small slot in the plastic threaded tubes. One needs to wiggle the valve until the sheet metal rear wall fits in. Then the valve can be slid into position. Attach the mounting screw, hoses, top, power cord and try it out.

BROKEN BAFFLE

  • Customer: DARLENE from SARASOTA FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
BAFFLE JUST SNAPPED INTO PLACE.....SO EASY!

Washer would stop at different times with code FH

  • Customer: David from West Chester PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I unscrewed the three small sheet-metal screws holding the washer top to the frame and slid the top aft and laid it on the floor. Then I took fine sandpaper and cleaned the plug contacts from the various components connected to the main control board. After five years or so I have found that most copper connectors will corrode and prevent electricity from flowing properly. That did not correct the problem. I checked the flow control device and it appeared clear and not binding. Then I pulled the drain pump filter and it was clear. I could hear the water pump running and the water flowing out the normal rubber hose. But the washer would stop three or four times during a wash cycle. Pressing 'RESET" and "START" would start the washer again. At the end of the cycle my wife noticed there was water in the washer tub. It had to come in via the water control valve. This is the valve you screw the hot and cold water hose into. It is a ice blue color and held in by one screw. I unscrewed the two hoses and removed the one screw. Then I had to slip the black supply hose from the valve leading to the flow meter. I disconnected the four electrical connectors and installed the new valve and found the screw hole did not align with the screw hole in the washer frame. I used a eighth-inch metal drill and drilled a new hole which lengthened the slot that the mounting screw normally went through. After I re-connected the hot and cold water lines to the valve I turned the water back on and put the top back on the washer. The washer worked like new. No stops. I did notice before changing the valve the water would flow into the washer tub like beer coming from a tap. After installing the new valve the water flowed in at three times the rate like a garden hose.

I was having the hf code constantly beeping and couldn't run a full cycle.

  • Customer: JANICE from MANHATTAN KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I opened the top by taking four screws from the back and lifted the top. The part to be replaced was clearly in view. I opened the clamps on the hoses, pulled the hoses off, removed the wires, and reversed the process with the new part. The washer works great now! I ordered the part on a Friday, and it was delivered the next day, even though I didn't pay for overnight!

The washer would slowley fill with water when idile

  • Customer: James from DeBary FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced water valve new valve had different electrical connections so I had to replace the connectors job took about 20 minutes. Washer is now operating correct
All Instructions for the 11042822201
136-150 of 158