Models > 11042822201 > Instructions

11042822201 Kenmore Washer - Instructions

All Instructions for the 11042822201
181 - 185 of 185
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer would not drain at all. Impeller spun on shaft.
The difficult part was getting the water from the washer without making a huge mess. I used a shop vac loosened the cover on the filter/strainer assembly use the shop vac to suck up the water before spills all over. if the tub is full I dumped my shop vac twice total. 1 Remove pedestal drawer 2 removed lower cover to expose mechanicals and pump assembly 3 vac out the water by using above procedure. 4 rotate hose clamps to a position where you can get the needle vice grip on them/remove hose clamps. 5 lift cover exposing electrical connections on the pump assembly depress tab slide connector out. 6 remove 1 torx head screw securing pump to base of washer. 7 remove pump assembly. 8 Reinstall in reverse of above instruction. I also took the lower tub hose off and washed, bleached along with hot water to. clean it
Parts Used:
Drain Pump Kit
  • Jeffrey from Marshfield, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Water comes into washer eben when no in use.
I followed the online videos and did the install in about 10 minutes. I did not need to drill a new hole for my particular model as others have needed. It was a basic take the old valve unit out and install the new one.
Parts Used:
Water Inlet Valve
  • William from Austin, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
door latch not closing or not releasing
Unplug electric. Open door. Peel rubber bladder back from washer door seal enough to expose wire retension ring. Remove three screws that hold door latch. Remove latch. Remove three wire harnesses. With new latch, reattach wire harnesses. Insert latch. Secure to machine with the three screws. Refit door seal and secure with retension ring. Plug in electric. Done.
Parts Used:
Door Lock Latch
  • Joanne from Bensalem, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
washer weren't drain
Had to open the panels, remove the old drain pump and install the new one. Remember if there is water still in the hose to either take it out with a wet/dry vacuum or put towels under neither to sook the water. 15 minutes of work and your done.
Parts Used:
Drain Pump Kit
  • JOSE from WOODBURN, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Warn Out Baffle
I saw a u tube video and followed the presenters instructions. Very simple instruction very simple repair. The whirlpool duet is a well designed machine with the mechanical parts easily accessible. I know if if would have had a professional service come and repair if it would have cost several hundred dollars. It cost me the parts, $50. 00 (That was for the 3-pack of baffles), 1 beer and my time. "Easy fix".
Parts Used:
Baffle Set
  • Daniel from Half moon Bay, CA, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 11042822201
181 - 185 of 185