10650037002 Kenmore Refrigerator - Instructions

Unplugged Refer...Cleared top shelf...removed screws/covers to expose thermostate and capilary tube...removed old thermostate takeing care to notice how Capilary tube was routed and electrical connection were made (wire color coding)...removed sheath on old capilary tube and installed on new, always making sure to not "kink" tubing...installed new part just as the old one was...plugged refer back in and enjoyed trouble free operation.

My fridge is a little different from the video model. The Controls in the fridge are located on an "arm" which swings down when the two screws are removed from the sides. It was not necessary to remove a front plate or knobs. However, I found when I got in to it that the old timer was not held by screws, but by plstic posts which had these "speed nuts" on them. This is a little metal plate which fits over the plastic post and bends to lock it in place. When you try to remove it, it acts like a barb, holding the little sucker on. I ended up bending the ends of those little suckers up tight against the post and twisting and pulling with needle-nose pliers. I broke one post like others before me commented, but one stayed intact. The only break at the top, so there ie still post left to hold the new timer. Once it was off, I was able to replace easily. The directions for choosing the right prong were a little confusing, but follow your gut and go with the wire colors. My schematic found in the bottom of the fridge did not look like any of the drawings, but I could match the wire colors. I also asked "Just Ask" for help, to make sure. My gut instinct was right. My fridge is now working again beautifully. If a housewife with no appliance repair knowledge can do it, so can you. I fixed my dryer with PartSelect too!I will never call another repair man until I have checked this site to see if I can do it myself. Bet I have saved $600 so far at least!

The ice maker stopped making ice. Cold water was still available at the freezer door dispenser which seemed to isolate the problem to the ice maker control board/motor. My ice making unit was not identical to the one in the video, but close. After disconnecting the power, I was able to replace the control board/motor without having to remove the entire ice making unit. Total time for repair was under 15 minutes.

Undid the bolts to the ice maker, unplugged it and took it out of the freezer. Removed the cover, unplugged the motor and unscrewed the motor from the casing. To install new motor screw it into the casing, plug it in and replace the cover.

Heard double clicking sound every couple minutes. Unplugged unit then using a coil brush, cleaned all dirt, lint, everything from bottom of fridge. Finished with vacuum cleaner. Located start relay. It was on the left side of the compressor. Pulled relay straight off of compressor, much like a plug from a wall. Unhooked two wires from relay. No need to disassemble old relay. Parts received from partselect.com go back onto compressor individually. Using the instructions provided, from the kit, select the correct parts for your unit and carefully attach them to the compressor. Plug in the wire to the relay, then following the instructions, attach the jumper wire and plug into the relay. The cover in the kit is a little tricky to put on but it will fit. Took me about 15 mins and the hardest part was getting the old part off. Plugged unit back in and it started right up. 24 hrs later, everything is working great!

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

Watched video of repair. Took all drawers and drawer holders out of freezer to acesss back panel. Removed 6 screws from back panel,slid up and out. Cut 2 wires to remove old bi-mtl defroster. splice the wires and attached new bi-metal def.

Using instructions found on the internet and the illustrated parts breakdown it was just a matter of following instructions.

Watched The Movie, Told Wife What To Do

Told Wife To Watch The Instructional Movie, Got Me A Beer And Watched Football. She Finished In about Thirty Minutes.Good Job

The icemaker on oour Kenmore was fading fast. Ice was only being harvested once every 4-5 hours instead of every two. Then finally it stopped altogether. I did some research and decide that it was the motor assembly that needed to be replaced. I ordered the part and within 3 days it arrived. Within 45 minutes I replaced the part with the assistance of the youtube video. I am not a Mr. Fix-it but this was fairly straight forward. I am now a hero.

internet search

Took two screwdrivers and inserted bottom of bezel pryed up and out gently. Removed (4) screws and unpluged (3) electronic plugs removing the circuit board. After you remove bezel & circuit board you have a chance to see what you are doing and get to the problem area with more ease. Remove old parts and reverse it putting the new parts. Process is very simple just pay attention to the order everything was removed. On my frig one of the plastic ears that hold the pin which holds the spring and door was broke. The piece I needed was no longer avaliable. I had to use a piece of the plastic from the old parts I removed, drilled a hole the size of the pin in it and glued it to the broken off ear. Put everything back together and I am pleased to say that everything works fine! So you might need to go a little MacGyver on it. All in all very simple fix.

Popped the cover off took panal off to access ice door screws.Removed old parts and replaced with new kit.Works fine now.

Removed the nut holding the plastic cover plate at the top of the door. Removed the 3 nuts holding the latch to the fridge. Lifted the door up and laid it on its' side. Removed the nut holding the door cam and replaced it with the new one. removed the nut holding the lower door cam and replaced it. Put a little vaseline on both cams and re-in-stalled the door. Took less than 15 minutes and the door is like new. Watching the video on the web site was perfect.