10650037002 Kenmore Refrigerator - Instructions

Just watch video from part select and following the instruction to replace the control and motor assembly.

I removed the ice maker unit completely from the freezer, following a Utube repair video that I found. I originally thought it was just the control board that was defective, because on examination, found a burned-out copper trace on the board, as well as a burned-out plastic connection point. Installing the new parts was a breeze. This icemaker is pretty foolproof, with plastic tabs that line up with the housing. a matter of lining up the screw holes was all that was necessary. Only problem I had was attaching a plastic cover that shields the electrical connection from the water. Once all was installed, I had to wait overnight for the icemaker to make ice. We've had ice ever since! Thank you Partsselect for very courteous and fast service!

There are two tabs that hold the icemaker to the rails it sits on. I use a small screwdriver and pushed the tabs up to release the tray and slid the Ice maker out. the cover over the control motor just pops right off. Then I removed three screws from the control motor pulled it off and put the new on, replaced the screws and put the cover back on and slid the icemaker back into the rails. I shut the freezer door and within the five minutes it took me to put my tools back in the garage, it was dumping ice. Very easy to fix. You do not need to remove the screws that hold the icemaker to the tray.

removedicemaker and unscrewed 3 screws hill ding motor assembly and control module to ice maker . nstalled new part and attached it with the 3screws. reinstalled ice maker and ice making cycle began almost immediately.

Removed ice maker and installed new part

I watched the video and removed the tray, but there were no screws underneath it! We tried prying it off with no luck, and then I read the directions from another customer. We removed the door handle, pressed down on the dispensing unit while using a flat head screwdriver to pry off the dispenser unit at the bottom (There are two little slots where the screwdriver fits perfectly.) I was afraid of the thing cracking since it is so old, but it did fine. This was the only hard part. After this was off, the rest of the repair followed the video exactly and it was super easy and took about 5 minutes! As I was detaching the old control bracket, I saw that it was completely broken on the right side. I knew then that this was the correct fix. It was an incredible moment when we tested the dispenser for the first time and water came shooting out! Thanks for your help on this - I would have never dreamed doing a repair like this before, and now i know I can do it.

Turned off the icemaker and took out the hex screw at the back of the unit that held the cable guard. The ice maker was easy to slide out after releasing guide locks on each side of the unit. Pulled the unit forward and released the electrical connection. With the unit on the cabinet, I removed the motor housing cover. Took out the 3 scews holding it in place and the old motor was out. Just reverse the steps putting the new one in. In an hour or two we heard ice dumping into the holder.

watched the video and went very well. No problems. I am sort of handy at repairs, and found this relatively easy.

Removed icemaker, replaced motor and reinstalled. Very quick delivery of parts, fit perfectly.

replaced the motor control assembly and it works great

First I watched the little video that was available when I bought the part on line. Though the job was easy, it was a VERY good idea to watch the video. Just makes you more confident to do the job well. The whole thing was done very quickly and to satisfaction

I followed the video. And it was a big help

I replaced the motor and everything is working great!

I removed the flapper door. I removed the screw to remove the wire connection. The ice maker slides out easily. I disconneted the power wires. Removed the motor cover. Removed the 3 phillips screws. Replaced everything in reverse order. I unplugged the unit to reset the LED panels. The ice maker is still not making ice.

After my ice maker just quit working I did some troubleshooting based on the users manual. Found all the electronics to be working fine so I took out the ice maker to see if the water fill tube was frozen, it was not. Next I took off the motor access cover to discover the gear that rotates the spindle was pushed out further on it's drive shaft so it was not meshing with the motor drive gear. I pushed the white gear back on further only to discover the small locking tab on the shaft was broken off allowing the gear to slip outward and become unattached. Had to order a complete motor/gear assembly, installed in 20 minutes and all is fine again. Easy fix.