652226-1-S-GE-WR17X11267        -Ice Funnel
652226-1-S-GE-WR17X11267        -Ice Funnel 652226-2-S-GE-WR17X11267        -Ice Funnel

Ice Funnel

PartSelect Number PS652226

This paddle, when your glass is pushed against it, activates the dispenser to release the ice through the funnel.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Water dispenser will not dispense water.
  • Ice maker won’t dispense ice.
  • Compare At

    $24.11
  • You Save

    $4.02
  • Your Price

    $20.09
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 7 reviews What's this?
1-7 of 7
 

27 of 34 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerJames from Malabar FL

Ice chute flapper not closing causing water dripping to floor and ice chute freezing up solid

I followed the video instructions for replacing the Flapper Valve and solenoid that Part Select suggested. It was one of the best DIY Reapair Sites I've used. Thank you

Help other customers find the most helpful instructions.

Were these instructions helpful?

21 of 36 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerSTEVEN from CLARKSVILLE TN

Trying to defrost the water line in the refrigerator door I melted (deformed) the plastic parts.

I carefully removed the trim from around the dispenser area then freed the catches in the top of the electronic card. I leaned the card forward and disconnected the electrical connections, then removed the card. I removed the four screws holding the shield to the door and removed the shield. Then I removed the funnel from the shield and removed the spring from the old funnel and placed it on the new one. I removed the light and socket from the old shield and installed the in the new one, then installed the new funnel on the new shield, used the four screws to install the assembly on the door and replaced the trim piece.

Help other customers find the most helpful instructions.

Were these instructions helpful?

17 of 32 people found this instruction helpful

Parts Used

  • Ice Funnel

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerDavid from Sparks NV

Replace broken ice funnel dispenser cradle

Removed outer trim by pulling it carefully out of its clips. Then disengaged the electronic display card by grabing the bottom of the card to disengage the card from the upper clips. I leaned the card forward and disconnected the wire connectors. Removed the 4 screws to take off the frame that contains the funnel. Remove the broken funnel from clips. Note study how the spring is engaged. Note position of the rubber funnel how there is a gap for the water tube. Removed the rubber funnel and attached to new funnel dispenser. Start at one end of the rubber flap and work around engaging the rubber into tabs. Replace the Funnel dispenser back into frame. Make sure the longer wire of the spring sits flat on the plastic frame and that the right elbow of the spring raps around the edge of the funnel. Secured the frame assembly back into the Refig using 4 screws and attached out trim starting withe bottom tabs engaged first.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 14 people found this instruction helpful

Parts Used

  • Ice Funnel

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJim from Glendale AZ

Ice funnel cracked

Followed video for replacing the ice chute flap solenoid replacement because getting to the ice funnel took same steps of disassemble. Looked at how the existing funnel was set in the housing, where and how one spring was located, where the switch and its activating arm on the ice funnel were located, took old one out and put new one in. Cleaned everything in process.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 12 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerDavid from Billings MT

Melted dispenser housing shield with hair dryer trying to thaw out frozen water line

Pull plastic trim piece off refridgerator door,unclip printed circuit board and remove wires unscrew dispenser housing,and remove. Transfer Ice funnel to new dispenser housing with old spring. Reinstall dispenser housing and printed circuit board.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 11 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

Customerjoseph from HAMPTON VA

Broken dispenser engager

Pretty easy to repair. Only took a few minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 30 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerChris from Old Hickory TN

Service tech melted the funnel and housing for the ice maker

The trim, funnel and housing were removed. I exchanged the small electrical part to the new housing and reinstalled the housing, funnel and trim. It took longer to get the tool then it took to make the repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-7 of 7