Models > A4425GDTABB

A4425GDTABB General Electric Refrigerator - Overview

Get Parts and Repair Help for A4425GDTABB

If you know the refrigerator repair part you need, you can browse the list of all parts on the A4425GDTABB, or you can search by name or part description. You can also find your part by where it is located on the A4425GDTABB by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for A4425GDTABB parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$9.20

Temperature Sensor

Also known as Thermistor. This part is used to sense the temperature in the cabinet.

$29.00

Ice Bucket Auger

When activated, the auger rotates and pushes ice out of the bin through the chute to the user.

$10.25

Defrost Thermostat

This part acts as a safety device against over heating in case of mechanical failure.

$18.07

Drawer Slide Rail - Right Side

$151.68

Main Electronic Control Board

This board controls the operation of the unit. Note: This part has been updated by the manufacturer. It may differ in appearance but will function the same as the original.

$4.05

Bearing Slide

Sold individually.

$16.32

Drawer Slide Rail - Left Side

When looking inside the fridge, this white drawer slide rail is located on the left side of the refrigerator. Rail ONLY.

$31.30

Dispenser Door Solenoid Assembly

This part is a possible option when ice door won't open or shut properly or when water is not dispensing.

$6.20

Dispenser Door Assembly or Flapper

This part mounts in the ice dispenser. **** The crank no longer comes with this part. You can use original crank. The crank is sold separately depending on model number of appli...

$144.30

Ice Maker

Replacement icemaker kit - electronic. This kit includes a 4 pin round plug-in connector, 6 post plug-in connector, tube and fill cup.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Plastic Auger blades broke in ice tray

  • Customer: Tim from Newport News VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 275 of 279 people found this instruction helpful
I used a digital camera and photographed the assembled unit and the metal blades before I started the repair. Then, I removed the top screw on the clear shield. Flip over ice tray and removed two Phillips screws on bottom. Exterior plastic white cover comes off next. The cover sides have hard push-in white plastic tabs. Push them in; pry up top cover with sm... read more

The refrigerator made continous "whooing" sounds that increased and decreased in pitch. Sounded like a ghost. Would keep us up at night. Also noticed that the heater was not heating under the evaporator coils.

  • Customer: John from Holly Springs NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 274 of 302 people found this instruction helpful
After checking the stories, the consensus of opinion was to change the mother board. I had a tremendous help from Tom Paone at quality@applianceeducator.com. He also told me to change the motherboard but to make sure that the coils were totally defrosted before starting up the refrigerator after changing the board.

Took off three nuts around the b... read more

flap to ice dispenser would not close

  • Customer: Bill from Cleveland Heights OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 172 of 187 people found this instruction helpful
The flap to the ice dispenser would not close, which allowed the ice dispenser to frost up, freezing the water dispenser.

This was a simple fix. The solenoid had stopped working, so it would not automatically close the door flap. I read some posts on this site that suggest that you had to remove the trim around the entire dispenser to get at the... read more