Tilt-Lock Hinge-Mounted Surface Burner - 8" WB30X354
★★★★★
★★★★★
Rated by 16 customers
Easy
30 - 60 mins
Ratings submitted by customers like you who bought this part.
$
116.89
On Order
Get FREE EconoShip on orders over $100! T&C apply
PartSelect Number PS244048
Manufacturer Part Number WB30X354
Manufactured by
GE
Product Description
Tilt-Lock Hinge-Mounted Surface Burner - 8" Specifications
This kit includes an 8", three wire, 2450W surface element. This low rise element has an attached trim ring, and a terminal block with all three-wire units.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Element will not heat
This part works with the following products:
Range.
This part works with the following products:
General Electric, Hotpoint, Kenmore.
Part# WB30X354 replaces these:
AP2634795, 2520, WB30X354, SX15, WB30X0139, WB30X0140, WB30X0146, WB30X0147, WB30X0199, WB30X0200, WB30X0223, WB30X0302, WB30X0303, WB30X0306, WB30X0307, WB30X0316, WB30X0317, WB30X0353, WB30X0354, WB30X139
...
Show more
, WB30X140, WB30X146, WB30X147, WB30X199, WB30X200, WB30X223, WB30X302, WB30X303, WB30X306, WB30X307, WB30X316, WB30X317, WB30X353, WB30X354R, WB30X5004, WB30X5005, WB30X5014, WB30X5015, WB30X5018, WB30X5019
Show less
Customer Reviews
Average Rating:
2 Reviews
★★★★★
★★★★★
4.0
Filter By Rating:
-
5 Stars
-
4 Stars
-
3 Stars
-
2 Stars
-
1 Star
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Nowell K - February 9, 2022
Verified Purchase
Works but sort of.
The burner works. I think my controls at the higher settings could be bad. Have no hi or 2. Its an old stove and oven. Probably 50 years. Happy you had a part for me.
★★★★★
★★★★★
Marvin S - May 27, 2019
Verified Purchase
Thx
Was what I wanted
- < Prev
- 1
- Next >
Back to Top
Customer Repair Stories
Average Repair Rating: 3.7 / 5.0, 16 reviews.
What's this?
Sort by:
- < Prev
- 1
- 2
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Replaced hinge mounted burner
Parts arrived bent and element had tape residue on it. After approximately 1 hr. I was able to clean, make parts straight and install it.
-
LUISA from EDEN, NC
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced old burners
Both the eight inch burner and the the six inch burner were not an exact fit. I used the old rings and the new burners. The eight inch burner fit well with the new drip bowl;however, the six inch burner did not fit with the six inch drip bowl and I had to grind off about an eigth inch from the diamiter of the drip bowl. I replaced most al
... Read more
l the wiriing and after I get the lower oven element rebuilt it will be ready for a test drive ..can't wait!
Read less
Other Parts Used:
-
Terry from Ulen, MN
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Change element and two burners
It was pretty easy. I just had to remove two screws, remove old element, connect new element and put screws back on. For the burners all you had to do was disconnect old one and reconnect new ones. The parts even included new ceramic covers for the wires.
Other Parts Used:
-
Jason from Taylors, SC
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set, Wrench (Adjustable)
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
50+ Yr Old Cooktop Burner had one of its two coils burn out
The hardest thing was finding the part to order! The GE Cooktop is from 1957 when the house was built. I followed the instructions that came with it. After seeing where the screw on hinge was supposed to be, I cleaned away the caked grease and finally saw the screw. I had to use a nut driver to remove it since it didn't have a slot for a
... Read more
screwdriver. Once that screw was out, the rest was easy. Before disconnecting any wires, I laid the new and old parts beside each other and drew a diagram showing where each wire (red, black & white) connected. It was a bit scary stripping the wires since they were old and fragile. It said to bend them into a "U" and solder but I didn't have soldering skill or equipment so I just tightened the screws holding the wires carefully. The connections are all nicely isolated in the bakelite insulator so it didn't seem cruicial. After working the new unit into place and turning on the power (at the circuit breaker), the burner worked perfectly. The replacement part looked exactly like the original. I was so amazed to be able to obtain the replacement burner after all these years! Thank-you PartsSelect!
Read less
-
Barbara from Smyrna, GA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
22 of 25 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner element was blown
Remove the old element by removing one screw and inserted new element and replaced the screw.
-
Pierre from South Burlington, VT
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burnt Burner;
Transfered wires from the old burner to new burner followed the color code. Each burner takes about 10 min. to replace.Part select thank you for the great service you are providing.
Mory
Mory
Other Parts Used:
-
Mory from Costa Mesa, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
2 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Find, Order, Receive & Replace electric stove burners
Teh instillation was a simple matter of removing the old burners and replacing them with the new ones. Removal required the screw connector on each burner ring to be loosened and the reverse done when the new one was installed. The hardest part was finding the correct burners since the Model number of the stove was not in anyones file.
... Read more
This web site provided adequate pictures of the part to permit identification of the likely part to order. Thanks.
Read less
Other Parts Used:
-
Harry from Catawissa, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
not have full output
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the four wires The element i request was 3 elements and i received two element but it was very easy i connect only the 3 wires.
-
George from Tonawanda, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner element damaged and needed replacement.
This part has the trim ring attached. My old element had the trim rim detached. This new part still fit my stove top and works fine.
-
Donald from Holmdel, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old surface burner burned out one of its two circuits.
I unscrewed the old burner from the stove, took off the three wire to the heating element marking down where each colored wire went, taped off the exposed wires, ordered the new burner, and waited for it to arrive. When it got here, I installed it, and believe it or not, the new burner works just fine!. End of exciting repair story.
-
James from Houston, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- 2
- Next >
Back to Top
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bill Odenbach
February 20, 2020
The u shaped clip bronze in color looks like it attaches two coil leads together. Is this correct and if so which 2 leads are connected? Our new burner does not work on 3 heat settings. Looking at the picture i cannot read the instructions that are included with this element. Can you somehow send instructions?
For model number WB30x354
Hello Bill, thank you for writing. Unfortunately we do not have the exact return instructions for that part number however we located a repair video that may assist: https://www.youtube.com/watch?v=9921quu0ZIw.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Griffin
June 12, 2019
Does this part come with a trim ring or do I have to buy it separately?
Hello Griffin, Thank you for the question. The element comes with the ring as pictured. Hope this helps!
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Back to Top
You May Also Need
?
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS244048
Manufacturer Part Number: WB30X354
Manufacturer Part Number: WB30X354
Brand
Model Number
Description
Back to Top
Tilt-Lock Hinge-Mounted Surface Burner - 8"
$
116.89
On Order
✖
Stock Status
In Stock
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.