Models
>
1J4081M1
1J4081M1 General Electric Range - Overview
Sections of the 1J4081M1
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
Bake Element
PartSelect #: PS249483
Manufacturer #: WB44X5099
This closed hinged-style bake element has screw in terminals.
$82.73
In Stock
Tilt-Lock Hinge-Mounted Surface Burner - 8"
PartSelect #: PS244048
Manufacturer #: WB30X354
This kit includes an 8", three wire, 2450W surface element. This low rise element has an attached trim ring, and a terminal block with all three-wire units.
$116.89
In Stock
Broiler Pan - Large
PartSelect #: PS1517612
Manufacturer #: WB48X10056
This large broiler pan is found in the bottom of your oven and is used to catch drippings from broiling foods. This part includes the grate and bottom pan and is made of porcelain. The grate measures ...
$30.07
In Stock
Bake Element
PartSelect #: PS249422
Manufacturer #: WB44X196
This bake element has screw-on terminals.
$85.60
In Stock
Trim Ring - 8"
PartSelect #: PS244459
Manufacturer #: WB31X49
This 8 inch low rise burner trim ring is intended for use with attached style low rise tilt lock surface mount burners on GE electric ranges.
No Longer Available
Questions And Answers for 1J4081M1
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 1J4081M1
[Viewing 5 of 5]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The lower bake element burned out.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, reconnected the wires to the new element, reattached it to the oven and voila!
It worked. What was really cool, once I ordered the part, I received it in only two work days!
Goo ... Read more d job folks!
It worked. What was really cool, once I ordered the part, I received it in only two work days!
Goo ... Read more d job folks!
Read less
Parts Used:
-
Carlos from Southaven, MS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
67 of 72 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
50+ Yr Old Cooktop Burner had one of its two coils burn out
The hardest thing was finding the part to order! The GE Cooktop is from 1957 when the house was built. I followed the instructions that came with it. After seeing where the screw on hinge was supposed to be, I cleaned away the caked grease and finally saw the screw. I had to use a nut driver to remove it since it didn't have a slot for a
... Read more
screwdriver. Once that screw was out, the rest was easy. Before disconnecting any wires, I laid the new and old parts beside each other and drew a diagram showing where each wire (red, black & white) connected. It was a bit scary stripping the wires since they were old and fragile. It said to bend them into a "U" and solder but I didn't have soldering skill or equipment so I just tightened the screws holding the wires carefully. The connections are all nicely isolated in the bakelite insulator so it didn't seem cruicial. After working the new unit into place and turning on the power (at the circuit breaker), the burner worked perfectly. The replacement part looked exactly like the original. I was so amazed to be able to obtain the replacement burner after all these years! Thank-you PartsSelect!
Read less
Parts Used:
-
Barbara from Smyrna, GA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
22 of 25 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced lower element in GE Spectra range.
Hardest part was getting the wrong element and having to send it back and reordering correct one....too many variables. Two screws inside the oven removed, pull out range and take off back and attach new element to plug ins!
Parts Used:
-
Phillip from Greeneville, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
22 of 30 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!