| |
11 of 12 people found this instruction helpful
Parts Used
-
- Tilt Lock Hinge Mounted Surface Unit - 6"
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver
CustomerJohn from Granite City IL
Burner had shorted out
It was so easy. I turned off the power to the range, loosened the hinge screw and removed the burner unit from the stovetop. Next I removed the two spring clips holding the ceramic housing covering the three connectors. Then I loosened the three screws holding the 3 wire connectors to the burner, reconnected the 3 wires to the new burner unit, positioned the ceramic insulator housing and reinstalled the spring clips and finally replaced and tightened the hinge screw. It took about 5 or six minutes, max.
You can do this!
|
4 of 4 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerHarry from Catawissa PA
Find, order, receive & replace electric stove burners
Teh instillation was a simple matter of removing the old burners and replacing them with the new ones. Removal required the screw connector on each burner ring to be loosened and the reverse done when the new one was installed. The hardest part was finding the correct burners since the Model number of the stove was not in anyones file. This web site provided adequate pictures of the part to permit identification of the likely part to order. Thanks.
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:1- 2 hours
ToolsPliers, Screw drivers, Socket set, Wrench(Adjustable)
CustomerJason from Taylors SC
Change element and two burners
It was pretty easy. I just had to remove two screws, remove old element, connect new element and put screws back on. For the burners all you had to do was disconnect old one and reconnect new ones. The parts even included new ceramic covers for the wires.
|
1 of 2 people found this instruction helpful
Parts Used
-
- Tilt Lock Hinge Mounted Surface Unit - 6"
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver
CustomerLeonard from Easton PA
6" element burnt out
Finding a replacement element for a 30 year old GE electric stove was difficult to find. I was overjoyed when I found a replacement on Partselect! It was a simple "Unscrew, reattach wires and install" all in about 10 - 15 minutes all with a nutdriver. Plug in elements are common but to find one with screw connections is not easy, THANK YOU PARTSELECT! A $48.00 investment (Element with trim ring) was worth the cost compared to a $1,400.00 replacement. You just made a loyal customer, again, Thank You.
Lenny
Nazareth, PA
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:1- 2 hours
ToolsPliers, Screw drivers
CustomerTerry from Ulen MN
Replaced old burners
Both the eight inch burner and the the six inch burner were not an exact fit. I used the old rings and the new burners. The eight inch burner fit well with the new drip bowl;however, the six inch burner did not fit with the six inch drip bowl and I had to grind off about an eigth inch from the diamiter of the drip bowl. I replaced most all the wiriing and after I get the lower oven element rebuilt it will be ready for a test drive ..can't wait!
|
0 of 1 people found this instruction helpful
Parts Used
-
- Tilt Lock Hinge Mounted Surface Unit - 6"
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsNutdriver, Screw drivers
CustomerRonald from Cape May Court House NJ
Elements were burned out
Removed the elements from the stove and disconnected the wires. Reconnected wires to the new elements and reinstalled in the stove. I was very impressed with the delivery time. I ordered online at 3:00 PM and the parts were at my door at 9:00 AM the next morning. Greatest service I ever had from anyone! I am 250 miles from the warehouse.
|