Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS2085070
This broil igniter assembly comes with its own metallic mounting bracket and an seven inch long dual wire lead with a plastic plug.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
followed instructions from repair manual.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Removed oven bottom were you see the light glowing from then unscrewed igniter unpluged then took it out and put in new one went well i would do it again works great
First I called a local repair shop and after getting a 325.00 repair estimate I looked up your website and discovered that I could purchase the part for 46.00 dollars and followed the do it yourselfers imput Now thats what I call a savings
I simply pulled the stove away from the wall, disconnected the gas and electricity. Then took the pan out from stove. At which time I used a socket to remove the two srews and then unplugged the part from the back of the stove. After that, reattached the screws, plugged it in, reconnected the gas and electricity, and pushed the stove back against the wall. Fired up the oven and it has worked like a champ ever since!
1. Turn off the gas (propane)2. Unplug the oven.3. disconnect the gas line and pull the oven out.4. remove the back panel to access the igniter.5 disconnect the igniter.6. unscrew igniter/gas assembly and remove from oven (two screws).7. unscrew igniter (two screws)8. replace igniter with new.9. reassemble in reverse order.10. turn on stove.11. Happy wife, happy life.
First I unplugged the range, turned off the gas to the oven and disconnected the gas line from the oven. I pulled the oven out to gain access to the rear of the unit and unplugged the old igniter. Next, I removed the oven door, removed two screws to the floor of the oven and removed it. I then removed the metal covering above the gas component allowing full access to the igniter. I removed two screws from the igniter and removed it. I positioned the new igniter and replaced the two screws. I replaced the covering over the gas component, replaced the oven floor and put the oven door back on. I went to the rear of the unit and plugged in the new igniter. I then reconnected the gas line to the oven range and checked for leaks, No leaks were found and I pushed the oven unit back into place. I pushed the Bake button and the igniter started igniting the oven. Job completed.
Remove oven floor and bottom drawerremove 2 1/4-inch screws holding ignitorremove cover plate behind drawer to access P/JDisconnect plug remove ignitor and reassembleDid not have gas smell, but ignition took 6 minutes
removed 2 screws on element then unpluged it then replaced it with new one easy job
Make sure the knobs are all in the off position before starting the work. You may feel more comfortable shutting the gas valve off behind the stove or in the basement first, just make sure you fire the burner and let the gas that is left in the line burn off.Remove bottom pan in oven by sliding the pins (located in the back) towards you and picking up the back of the pan and pull it away from you, this will slide the pan off of the other 2 pins that you can not see on your end of the pan. Take the flare shield off from over top of the gas line (should be 2 nuts or 1 wing nut). Remove the screw or screws that hold the heat shield covering the ignitor wires and remove the heat shield. Unplug the ignitor. remove the screws holding the ignitor and remove it. Be sure to order the ignitor with the extra shield and make sure it has new screws, you may need to replace the screws. Try not to touch the element of the ignitor. it can be very brittle. It seems lengthy but is very quick and simple.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wire pull the old igniter out.Install new igniter, by mounting to frame with two screws, feed the two wire assembly through the hole behind the gas tube, reconnected the wires, oven started right up. PartSelect was great, received the part very fast and there feedback comments are a big help.
I unplugged the power to the stove first,I removed the racks and cover plate at the bottom on the oven. Located the 2 screws holding the element igniter in place. I pulled the stove forward and removed the back cover plate and unplugged the old element.Installed the new element and tested the igniter, special note my oven would not ignite the propane with the cover plate not first being installed. The igniter glowed but would not ignite fuel.
After reading how others replaced their defective Gas Oven Igniter, I decided to attempt the project. My only mistake was Removing the Oven Door. Though it came off with ease, it was a complete bear to put back on. Once I removed the oven door, I located the two phillips head screws that held the bottom oven floor in place. One screw came off without much effort, however the other stripped and had to be drilled out. After removing the oven floor plate, I quickly located the Igniter and using a nut driver, unscrewed it. One of the two screws stripped on me and had to be replaced. The new part was put in position and the process was reversed. This is where I encounted a problem. After repeated attempts, I soon found that the oven door hindges had to be held in the open position with a flat head screwdriver in order to be put in place. I found no instructions or info on how to complete this process (even from Maytag) and only completed the tast by trial and error. I highly suggest NOT REMOVING THE OVEN DOOR to complete the repair. The repair itself is rather simple even with stripped screws.
I opend the bottom cover, which had for screws then , opened 2 screws that atached the igniter to the main gas pipe and pulled the whole wiring out and disconected the wiring , ordered the igniter two days later, I put the whole thing together in less than 5 minutes . put back the cover. and I tried it , everything was cool , accutaly hot and working .
Tested power coming into unit,then tested power going to igniter,both of which were good.Did a continuity check of igniter element and found it to be bad.Ordered one from PartSelect,recieved it in minimum time,removed the old one,installed the new one,works like a champ.
The oven was inconsistanty lighting and I could not predict when it would. After reading some repair reviews I determined that the problem was most likely the igniter. I purchased one from your site and it arrived the next day. Awsome! Had to take out six screws to get to the wiring and removed the igniter. The wiring was a simple plug. Replaced the igniter in about 20 minutes and the oven has been working flawless every since. THANKS!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.