Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 31203PAQ

31203PAQ Magic Chef Range - Overview

Get Parts and Repair Help for 31203PAQ

If you know the range repair part you need, you can browse the list of all parts on the 31203PAQ, or you can search by name or part description. You can also find your part by where it is located on the 31203PAQ by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for 31203PAQ parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$50.37

Oven Igniter - Vertical Mount

This broil igniter assembly comes with its own metallic mounting bracket and a 7-inch-long dual wire lead with a plastic plug. This part will need to be repaired if your oven eleme...

$18.24

Top Burner Igniter

This is a surface burner igniter, also known as a top burner ignitor and stove top spark electrode. It is used to generate the spark that lights the surface burner. If your stove will not start, element does not heat, or gas igniter glows but does not light, replacing the igniter can solve these issues. For this installation, you will need a Phillips screwdriver and needle nose pliers. First place the grate on top of the burner, then lift the burner and disconnect the wires. Next remove the two Phillips screws from the bottom of burner, pull igniter out of the burner and wiggle in the new one. Refer to the installation instructions provided by the manufacturer for more instructions.

$3.02

Screw

This screw is sold individually.

$51.11

Oven Rack

This is a replacement oven rack and it is designed for use with ranges and ovens. This is a genuine OEM replacement part. The rack provides a level and stable surface for cookware inside of your appliance. Installing the new rack is simple, you slide it into the pre-existing tracks in your oven. It measures approximately 23 inches wide by 16 inches deep. This replacement part is made of metal and it is sold individually.

$6.49

Levelling Leg

This is a levelling leg for your oven, range, or stove. It is just under 3 inches long, is all black in colour, and is made entirely out of plastic. The levelling legs on your oven...

$6.18

Screw, 10-16 x 1

This screw is sold individually.

$40.09

SEAL- DOOR

This door seal is fifty-three inches long. It is all black in color and is made of rubber. There are metallic clips sticking out of this seal at various points. These clips help to...

$62.30

Burner Head Cap with Spark Electrode

This part distributes flame evenly to your cookware.

$36.32

Double Drip Pan

Sold individually.

$3.02

Screw

This screw is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven wouldn’t heat up properly

  • Customer: James from Berwick, ME
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 213 of 238 people found this instruction helpful
My oven has two igniters so I needed to determine which one was the problem.

Using the amp/multi meter I tested the connection between the igniters and the valve, with the oven turned on, to find the bad igniter. Depending on the model of stove you have, the amp reading you need for a properly functioning igniter will vary. My lower igniter read ... read more

gas burner ignitor failure

  • Customer: roy from East Providence, RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 120 of 134 people found this instruction helpful
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt ha... read more

Our oven would not heat up, smelled like gas.

  • Customer: Theresa from Yorkville, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 53 of 58 people found this instruction helpful
I removed the oven door, unscrewed a couple of screws, replaced the ignitor, put screws back in, done! Sometimes it would take my oven up to an hour to heat up and sometimes it just wouldn't heat up, just fill the house with a gas smell. Now, it heats up in about 3 minutes!! We were considering buying a new oven, we will just keep this one. $40.00 beats $70... read more