2078472-1-S-Whirlpool-71003424-Electronic Clock Control Board
2078472-1-S-Whirlpool-71003424-Electronic Clock Control Board 2078472-2-S-Whirlpool-71003424-Electronic Clock Control Board 2078472-3-S-Whirlpool-71003424-Electronic Clock Control Board http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/52303.gif

Electronic Clock Control Board

PartSelect Number PS2078472

This part is also known as the "brains" of the appliance.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not program.
  • Compare At

    $436.33
  • You Save

    $72.72
  • Your Price

    $363.61
In Stock
Order within the next 10 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.3 / 5.0, 51 reviews What's this?
1-5 of 51
 

48 of 49 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerCheryl from Mesa, AZ

No clock display

1. Turned off the circuit breaker for the oven.
2. Opened oven door used a phillips screwdriver to remove four black screws from under the top panel.
3. Lifted panel slightly & removed from oven.
Removed four screws using 1/4" nut driver to remove old display unit. Disconnected three wire harnesses.
4. Connected three wire harnesses to new display unit & replaced four nut screws.
5. Hang the top panel on the top of oven & replace four screws removed in step 2.
6. Turn on the circuit breaker for the oven.
("Very easy! I'm a 63 yr. old woman!)

Help other customers find the most helpful instructions.

Were these instructions helpful?

19 of 19 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerHerb from Seminole, FL

The clock and temperature control became dim and unreadable.

First I turned off the power at the breaker. Then I removed the 4 screws holding the panel in. These screws are located under the panel and accessed when the oven door is opened. The only caution is not to take all the screws out. Just the 4 that hold in the front panel.The panel came off by lifting it and pulling it slightly forward. Then I removed the 3 wiring harnesses. I then used a 1/4 inch socket wrench to remove the (4) screws and replaced the clock unit with the new one. I tightened the 4 screws, re-installed the wiring harnesses and swung the panel back in place . I then locked it in place with the 4 screws on the bottom of the panel. When I turned on the power and my wife saw the lit up clock she was so happy! End of story.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 12 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerJohn from Tempe, AZ

Clock digital read out dim to non-existant

This was soooo easy, yes even you Mr. All thumbs, can do it. First it was nice to receive the exact parts I needed from PartsSelect. I needed to take the 4 screws that held the wall oven in place and pull it out about 1". Then, using a battery powered screw driver I removed 4 screws for under the Clocks panel, (you'll need to open the door, can you handle that?). After you've done that simply lift the Glass up and off by grasping the panel and with thumbs on the bottom tilt bottom toward you as you lift up, comes right off. Now disconnect the wire ribbons (4 of them) to seperate the panel from the oven and set the panel down on a towel on the table. Now using a nut driver take out 4 "nuts" and replace the clock card. Be sure to wipe off the INSIDE of the glass panel while you have the card out, and wipe the cards glass so the digital readout will be crystal clear. Re-assemble in the reverse order and you are done. Should take you less then 15 minutes and your wife will think you are a hero! (or you wives can do it and impress the husband!)

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 16 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerRobert from South Euclid, OH

Burner will not heat, display will not light

Two separate problems. The display gradually dimmed over time and finally went out completely. It was really easy installing the new display module. I analyzed the old one and found an 68uF electrolytic capacitor (<$1) that was bad. Don't know if any other component was bad. In looking at the display module it seems it was way over-priced at over $200. The second problem is that one of the small burners had a open heating wire. The installation of the new burner was OK except the new unit did not have any clips to hold it in place. I couldn't transfer the old clips over. So I just placed it under the holding bracket and hoped that it wouldn't move while I was putting the unit back in place and it didn't. So that is working OK now.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 8 people found this instruction helpful

Parts Used

  • Electronic Clock Control Board

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerRobert from LEXINGTON, MA

The cooking/time display had become very dim

1. Turn off the circuit breaker for the oven
2. Open oven and using a phillips screwdriver remove four black screws from under the top panel.
3. Lift panel slightly and remove from oven. Disconnect three wire harnesses.
4. Remove the old display unit by taking out the four screws using a 1/4" nut driver.
5. Install the new display unit using the four screws
from step 4.
6. Hold the top panel close to the top of the oven and attach the three wire harnesses.
7. Hang the top panel on the top of the oven and replace the four screws removed in step 2.
8. Turn on the circuit breaker for the oven.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 51