| |
16 of 21 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerSusan from Hollywood FL
The plastic knob broke and wouldn't grip the steel movement
all i did was put the three pieces together (1-2-3! so easy) and attached to the metal piece of the dryer. now i can set the dryer to any temperature and time i need!
|
5 of 5 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJorge from Longwood FL
Timer knob broke from the middle.
Researched for the part numbers and found the parts needed. In this case the timer knob is made up of 3 separate pieces that easily snap together.
|
2 of 2 people found this instruction helpful
Parts Used
-
- Timer Knob Insert Cap
- Timer
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
CustomerDavid from Mentor OH
Washer would stop running during the wash cycle
1, Unplug unit from power outlet. 2, Removed 3 screws on the top back control console, 3, pushed bottom section back (standing in front) and tip top section foward, console then will lay flat on top of the washer, 4, remove wire connector, 5, remove 1/4 " screw lower left side, 6, lift locking tap up and slide timer to the left. 7, Set new timer in place and reverse the procedure starting with step 6.
|
2 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customerdawn from frisco CO
Time knob had broken
Removed clip that held timer knob in place, replaced timer know with new one and reinstalled clip. The snapped on the new cap. Took a whole minute to do.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerWayne from Hamilton MT
Knob retainer hole was broken
Ordered the part..... waited a few days fro it to arrive, (it came quite quick considering). Sat down in my easy chair and assembled the knob and gave it to my wife to slip it on the dryer. Whew, I was beat.... hehe
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
Customerdenise from lake worth FL
Knob not working and would not turn off dryer
Wow it was the easiest thing I have ever done.. I am NOT a DIY person.. Company wanted $108.00 to do, it cost me less than $20.00 and 2 minutes.. I have told everyone I know!!! Thanks
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerJeannette from Carencro LA
The timer dial broke
I pulled the dial off. Fit the three new parts together. I put in stem of the timer and turned the dryer on.Very easy, No tools required except a screw driver to pry the old knob off.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerThomas J from League City TX
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers
CustomerWAYNE from PHILADELPHIA PA
Door would not lock, knob broken
called SEARS told part not available any longer. Would have to purchase new dryer. Also told part could not be ordered from MAYTAG due to age. Called PART SELECT and had new parts in four days. Put new knob on, Placed door lock in hole, JOB DONE (15 minutes) saved $ 500 to $600 on new one. Wayne
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerMelissa from Albuquerque NM
Broke the knob for dryer selection
hey this was so easy that 6 year old could put the parts together..I loved this! No repairman and no going to an appliance store and getting frustrated.Easy as pie!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers
Customerjim from oklahoma city OK
Broken control knob on washing machine
the pictures on your web site allowed me to positively identify the 2 pieces quickly and surely. replacement was a snap and took less than 2 minutes. Thanks!!
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerMichael from Savannah GA
Plastic know stripped so mechanism would not turn
I only needed to remove the old knob and replace with the parts purchased. The hardest part was finding the part and once I found PartSelect that was easy. My wife figured we would never find the parts for this old driver. Thanks for the help.
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerTom from Hickory NC
Dryer knob just spun
Pulled the knob off and found that it had split. Went online and found the part required plus new grip and cover cap. Parts arrived in two days, snapped together and slid onto the pin.
All fixed!
Thanks!
|
0 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerKarl from Los Angeles CA
Timer dail skirt broke
Inserted Timer Knop Into Timer Dial Skirt and Attached Timer Knob Insert Cap, then I placeed the whole knob onto the timer of Dryer
|