Models > LAT5006AGE

LAT5006AGE Maytag Washer - Overview

Get Parts and Repair Help for LAT5006AGE

If you know the washer repair part you need, you can browse the list of all parts on the LAT5006AGE, or you can search by name or part description. You can also find your part by where it is located on the LAT5006AGE by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LAT5006AGE parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$55.50

Mounting Stem/Tub Seal Kit

This kit comes with hub assembly, agitator seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace t...

$2.70

Screw

This screw is sold individually.

$15.20

Dryer Door and Washer Lid Switch Kit

This kit is simple on/off mechanism that prohibits the machine from operating when the door is open.

$15.41

Timer Knob

This part does not come with the top insert cap or the dial skirt.

$2.70

Hose Clamp

$2.70

Screw

This screw is sold individually.

$7.02

Timer Knob Insert Cap

This part is all white in color and is made of plastic.

$33.75

Tub Bearing Kit

This kit is used on 2-belt washers. It is recommended to change the seal kit at the same time.

$34.12

Lid Switch Assembly

This black lid switch assembly comes complete with a bracket, two switches, and a fuse. An open fuse might indicate that the lid switch is bad. The point of the lid switch is for ...

$6.91

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water leaking from around center shaft below fixed tub

  • Customer: douglas from bonita springs FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 354 of 364 people found this instruction helpful
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag washers, when I came a... read more

Washer Leaking and Spin Cycle stopping frequenly

  • Customer: Dan from Mason OH
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 123 of 128 people found this instruction helpful
* Remove front Panel
* Remeove two screws that allow the top to hing up.
* Loosen set screw on agitator (1/4" socket)
* Remove Agitator
*Loosen spanner nut from mounting seal with hammer and punch remember to loosen, turn clockwise
* Remove Inner Tub
* Losen Mounting stem with Hammer and Punch- Remember to loosen, turn clockwis... read more

Washing machine shut off at begining of cycle

  • Customer: Jason from Aberdeen MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 76 of 91 people found this instruction helpful
The washing machine was full of clothes, water, and detergent when it decided to stop working. I pulled the washer away from the wall (I recommend using two people for this), and removed the back access panel (two screws at the top and bottom). With the washer plugged into the wall outlet I used a multimeter to test electrical distribution through the syst... read more