Models > LAT3600AAQ

LAT3600AAQ Maytag Washer - Overview

Get Parts and Repair Help for LAT3600AAQ

If you know the washer repair part you need, you can browse the list of all parts on the LAT3600AAQ, or you can search by name or part description. You can also find your part by where it is located on the LAT3600AAQ by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for LAT3600AAQ parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?

Mounting Stem/Tub Seal Kit

This kit comes with hub assembly, agitator seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace t...


Drain Pump

This assembly uses 2 belts. Order belts if you notice wear and tear.



This screw is sold individually.



This screw is sold individually.


Hose Clamp


Tub Bearing Kit

This kit is used on 2-belt washers. It is recommended to change the seal kit at the same time.


Timer Knob Insert Cap

This part is all white in color and is made of plastic.


Damper Pad Kit

This damper pad kit is used for base support. It comes with three six inch damper pads, two little tubes of lubricant. NOTE: This part will need adhesive to stick it in place.


Outer Tub to Pump Hose

This hose connects the outer tub to the pump of your washing machine.


Spring Retaining Clip

This front cover spring retaining clip is not quite an inch long. It is made entirely of metal and is used for some washing machines.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water leaking from around center shaft below fixed tub

  • Customer: douglas from bonita springs FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 367 of 377 people found this instruction helpful
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag washers, when I came a... read more

Drum would not drain and there was a banging noise when the drum spun

  • Customer: Charles from Whitman MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 146 of 74 people found this instruction helpful
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes ... read more

Washer Leaking and Spin Cycle stopping frequenly

  • Customer: Dan from Mason OH
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 131 of 136 people found this instruction helpful
* Remove front Panel
* Remeove two screws that allow the top to hing up.
* Loosen set screw on agitator (1/4" socket)
* Remove Agitator
*Loosen spanner nut from mounting seal with hammer and punch remember to loosen, turn clockwise
* Remove Inner Tub
* Losen Mounting stem with Hammer and Punch- Remember to loosen, turn clockwis... read more