Quick Question!

Have you ever purchased from PartSelect.com before?

1482382-1-S-GE-WH12X10350        -Timer
1482382-1-S-GE-WH12X10350        -Timer 1482382-2-S-GE-WH12X10350        -Timer http://www.partselect.com/Schematics/GE/00124086i01.gif

Timer

Compare At

$140.22

You Save

$23.37

Your Price

$116.85
Order within the next 56 mins and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS1482382
Manufacturer Part Number WH12X10350
Manufactured by GE

The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.

This part works with the following brands: General Electric.

This part works with the following products: Washer.

This part fixes the following symptoms:

  • Timer will not advance.
  • Will Not Start.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.7 / 5.0, 2 reviews What's this?
1-2 of 2
 

47 of 53 people found this instruction helpful

Parts Used:
  • Timer
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers, Socket set
Customer: Michael from Snellville, GA

Replace timer module

Remove the knob. This is the hardest part. To remove the knob, unplug the washer and pull the unit out so you can get to the back. Stand on the right side of the machine and pull the knob out. It is retained by a nylon clip. Take a small flathead screw driver and use it to push the clip up from the open ended side. Not much force is required. It will pop right up. The clip has a hook on one side so if you try to remove it with needle nose pliers (like I did the first time) you will bend the trim on the knob and likely break the clip.

Once the knob is off, remove the dial with the pointer on it and set it aside.

With this done, remove the three hex screws on the back of the control panel. Then lift the plastic control panel up, then forward. This will allow you to lay the control panel on the top of the machine.

Remove the wire harness by lifting up on the retainer and pulling on the harness. Grip the harness not the wires. The harness seats with a good grip so you'll need to work it a little.

Remove the single retaining screw that holds the timer unit to the control panel. Once the screw is removed TWIST the timer unit to remove it. The timer is held in place by two retaining "prongs" that you will break off if you try to pull the timer off the control panel. Once free of the retaining prongs, the timer is off the control panel and you are ready to replace with the new one.

Install is the reverse of what you just did.

When you get to putting the knob back on don't forget to put the dial with the arrow back on first. This only goes on one way but it takes a pretty good push to get it to seat. Next, put the nylon retaining clip on the knob such that it's barely on and slip the knob on the timer post only to the point where you see the slot in the knob and the slot on the post line up. When the two slots are aligned, use the blade of the flathead screw driver to push the nylon clip into place.

Reseat and align the control panel, replace the three screws, plug the unit back in and you can watch the game while the little lady gets back to her washing. :) Just kidding ladies.

This is an easy repair that anyone can do with only a couple hand tools and a little patience. Getting the knob off is the hardest part and a little finesse will work better than brute force.

Have fun, you can do it.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

22 of 29 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: William from Hillsboro, OR

Gear teeth stripped out on both timer knob & timer.

Super EZ repair. The replacement parts were spot on perfect. I removed 3 screws, slid the panel off, removed a wiring harness, the reversed the procedure. I used a set of needle nose pliers to slip the locking ring on the knob, and Bob's your uncle, all done.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-2 of 2

Model Cross Reference

This part works with the following models:

PartSelect Number: PS1482382
Manufacturer Part Number: WH12X10350
Brand Model Number Description
General ElectricGBSR3140H4WWWasher
General ElectricGHDSR316H0WWWasher
General ElectricGHDSR316H1WWWasher
General ElectricGHDSR316H2WWWasher
General ElectricGHDSR316H4WWWasher
General ElectricGKSR3140H0WWWasher
General ElectricGKSR3140H1WWWasher
General ElectricGKSR3140H2WWWasher
General ElectricGKSR3140H4WWWasher
General ElectricGNSR3150H0WWWasher
General ElectricGNSR3150H1WWWasher
General ElectricGNSR3150H2WWWasher
General ElectricGNSR3150H4WWWasher
General ElectricS3700G0WWWasher
General ElectricS3700G1WWWasher
General ElectricS3700G2WWWasher
General ElectricS3700G4WWWasher
General ElectricWBSR3000G0WSWasher
General ElectricWBSR3000G1WSWasher
General ElectricWBSR3000G2WSWasher
General ElectricWBSR3000G4WSWasher
General ElectricWBSR3140G0WWWasher
General ElectricWBSR3140G1CCWasher
General ElectricWBSR3140G1WWWasher
General ElectricWBSR3140G2CCWasher
General ElectricWBSR3140G2WWWasher
General ElectricWBSR3140G4CCWasher
General ElectricWBSR3140G4WWWasher
General ElectricWHDSR316G0WWWasher
General ElectricWHDSR316G1WWWasher