270835-1-S-GE-WH1X2117          -Timer Knob Clip
270835-1-S-GE-WH1X2117          -Timer Knob Clip http://www.partselect.com/Schematics/GE/00122776i01.gif

Timer Knob Clip

PartSelect Number PS270835

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Timer will not advance.
  • Will Not Start.
  • Compare At

    $4.00
  • You Save

    $.67
  • Your Price

    $3.33
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.6 / 5.0, 19 reviews What's this?
1-5 of 19
 

128 of 157 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Mr Dennis from Twinsburg, OH

Knob would not engage, had to manually turn outer ring to start washer.

Used a screw driver and needle nose pliers to remove clip from behind the timer knob. Took 2 minutes to remove clip, i admit it was a little tricky but once you get a grip on the clip very easily removed. Replaced with new knob, old knob gear was completley stripped . put the new clip on and presto, Like brand new.A normal service call would of ran me 45.00 just to tell me what was wrong with the machine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

43 of 46 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Kristina from Pasadena, CA

Timer on the washing machine wasn't working properly. Just spinning around not catching to set wash cycle

I found Partselect and searched for what I needed. Wasn't quite sure I had the right timer, so I called and gave them the model number and they did a search and found the right one. I ordered the part online and a few days later the parts were delivered to me. The timer fit right in and looked just like the origninal. Within 30 mins. washer was back in service.
Another washer we have on the property wasn't agitating correctly. After taking off the agitator ( by pulling straight up from the bottom ) I found that the coggs on the agitator hub were all worn out. I removed the center screw from the shaft and pulled the old hub off. Installed the new one ordered from Partselect and washwer was back up and running in no time.

Help other customers find the most helpful instructions.

Were these instructions helpful?

32 of 42 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Gordon from BLUE DIAMOND, NV

Timer knob broke off where the dial compression ring fits.

All I had to do was pull out the broken timer dial assembly and push in the new one.

Help other customers find the most helpful instructions.

Were these instructions helpful?

34 of 63 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver
Customer: RICHARD from NEWARK, DE

Knob and timer di not work

remove back screws to control panel. unplug timer. pull bad timer out. snap new timer in plug in connector. reattach screws to control panel. put knob on timer

Help other customers find the most helpful instructions.

Were these instructions helpful?

21 of 26 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Clifford from Sun Valley, NV

Teeth on timer knob broke off

Removed timer knob clip and installed new dial and timer knob

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 19