Quick Question!

Have you ever purchased from PartSelect.com before?

11744544-1-S-Whirlpool-WP7432P109-60-IGNTR-OVEN
11744544-1-S-Whirlpool-WP7432P109-60-IGNTR-OVEN 11744544-2-S-Whirlpool-WP7432P109-60-IGNTR-OVEN http://www.partselect.com/Schematics/Maytag/51886.gif

IGNTR-OVEN

PartSelect Number PS11744544

This part creates the spark that lights the gas and starts the burners.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will Not Start.
  • Gas igniter glows, but will not light.

Compare At

$24.89

You Save

$4.15

Your Price

$20.74
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.2 / 5.0, 3 reviews What's this?
1-3 of 3
 

16 of 26 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Wrench set
Customer: Bill from Pearland, TX

Would not stop igniting even after fire was on

unplugged unit from wall, disconnected gas line, and untaped the vent. disconnect the control knobs and unplugged and removed the control unit from the main unit. pulled the main unit out from the countertop and set it on a table. disconnect the burners and spark iginiters from the main unit. undo screws holding chrome brackets and stove base, to access iginiter. disconnect wiring from igniter and the one screw, replace iginiter. reverse everything to re-install

Help other customers find the most helpful instructions.

Were these instructions helpful?   

9 of 12 people found this instruction helpful

Parts Used:
  • IGNTR-OVEN
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Pliers
Customer: Marlene from Dana Point, CA

Stove top gas burner ignitor only flicks but does not light burner

If you have a burner that begins to constantly flick without lighting, and/or flicks while you are lighting another burner, it is likely time to order a new ignitor. Once received, we first lifted the burner support rack, then the burner cap, then unscrewed the nut holding the metal bracket that holds the ignitor in place (years ago we had to "soak" the nut with a loosening spray prior to being able to unscrew it, so since then we do not tighten the nuts too tightly so that each nut is easy to unscrew by hand or with pliers if necessary). The previous steps allow one to lift the burner ignitor up and out of its resting hole. It will be connected to the electric wiring via a plastic connector. All one has to do is pull the wiring away from the ignitor and then push it up into the new ignitor. The plastic connector protects you from touching the live ends of the wiring. Voila! The burner lighted successfully.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 6 people found this instruction helpful

Parts Used:
  • IGNTR-OVEN
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Wrench set
Customer: Robert from Pleasanton, CA

As soon as the parts arived it tooks only 1 1/2 hours to get everything fixed

took the nuts off &replaced the new ignited

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-3 of 3