ZISW480DRI General Electric Refrigerator - Instructions

There were only 3parts listed to check omed out the defrost heater and thermostat ....thermistor checked bad ordered replacement took less than 2 minutes to replace after I defrosted it again runs fine

Adding a small amount of water to the filter would resolve the problem for a week or two. So, I thought this was an issue with the filter and decided to try the bypass cap to help zero in on the problem. The bypass cap had no instructions concerning the need for O ring so it was trial and error. The O ring was not needed. After installation of the bypass cap, no water flow resulted and I had to replace the filter. Intermittent problem continues.

Exactly as the instruction video said. I could have done it without the instructions but I would not have cut a piece off the two water lines and possibly had problems down the road. Also, I may not have figured out the easy way to remove the two lines from the valve body. I believe this is my 3rd time using your process and it's absolutely the best. I won't go anyplace else. Next project is probably replacing the ice maker.

We watched the video on your web site and was very helpful. We ordered the part from your site was here very quickly. It took us about Fifteen minutes to replace. Saved us alot of money. Thanks so much for all your help.

it was easy the only thing was i had to cut old harness to remove 2 wires that went to coil that had to go back in the new harness other then that a peice of cake.

Watched à video provided at your website. Removed te cover then removed 4 screws holding the control panel' snapped out the old flap and inserted the new one.

My son replaced both temperature sensors and the fridge works great now!!! Like brand new again!!!!

Removed frame, unscrewed the electrical panel, and popped the flapper off. Installed new flapper. Replaced the electrical panel and re-installed the frame.

Removed the ice maker control panel and accessed the flapper door, easy switch out for new door and seal. The 2 year old warped seal didn't close and so ice crystals formed in the freezer - new unwarped part and Ta-Da no more problems :)

1.Unplug and turn off water supply to refrigerator. 2.Remove several screws from back panel and remove panel 3. Remove water supply line from valve. 4. Remove screw holding valve on using 1/4" nut driver or socket. 5.Remove the 2 electrical plugs and 2 water lines from valve. 6.reinstall in reverse order. This is a 5 minute job at best. Good Luck! I had my fridge in storage for several years and when it froze it cracked the storage tank PS783769 I replaced it first and found valve was leaking after tank was replaced.

Remove outer trim of the in-door dispenser. Remove the electrics by popping it out and up. Remove the connectors. Remove the 4 screws that hold the ice funnel in place. Clean everything you can reach while you have this out. Remove the broken piece and note how the spring is hooked up. Remove the activation switch and reinstall the ice funnel and the spring. Reattach the activation switch and check it for proper activation. Reattach everything in reverse order.

Popped off the front frame and front of mother board. unscrewed the assembly to be able to lift up to get to flapper. Lifted it up out of the the way ( wires are attached so it may take one other person to hold it up out of the way). Pop out the old flapper and replace with new one. Easy !

Repair went exactly like the video. With this video it was easy to make the repair. There were no surprises or problems and I felt confident in the videos instructions. It was like pushing the easy button.

Part shipped in 2 days after requesting basic mail. Video was exremely accurate, no surprises. Valve replacement DID NOT fix my problem, however. I had to twist the water filter plug on and off a few times to release better pressure. My issue appeared to be with filter mount shut off. Still cheaper than a repair man!

Installed a dual water inlet valve.. by turning off the water and unplugging the refrigerator. use a nut driver to remove the screws and removed the connector to the inlet valve.. installed the valve and reverse the procedure. it was very ease also the Part Select troubleshooting information and instructions was very helpful..