Models > ZISB36DXA > Instructions

ZISB36DXA General Electric Refrigerator - Instructions

All Instructions for the ZISB36DXA
451 - 465 of 537
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ice machine flapper door solenoid burned up
Follow PartSelect video on website, had no problems learned a lot
Parts Used:
Dispenser Door Assembly or Flapper Dispenser Door Solenoid Kit Dispenser Assembly Crank
  • Troy from Tullahoma, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
would not "dump" ice cubes
I am more than 80 yrs, always thought I could fix just about everything--but, this looked complicated. Once I received the new icemaker; took a good look where the screw-holes, etc. were, then removed the "old" one. Took about 20 or 30 minutes, then the "new" one was easily installed.
Parts Used:
Ice Maker
  • Phayo from Lake Charles, LA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
summer cottage lost heat during winter inlet valve for icemaker froze
parts select delivery time unreal !!!!! ordered on a Tues. was here Wed !!!! Perfect fit, minor difference in tubing connection. Took more time to clean the floor once i moved the fridge than the actual repair. Thank you Parts Select, if i need more appliance repair parts, you're my first choice>
Parts Used:
Dual Inlet Water Valve
  • Robert from Waterford, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
My Auger was rusted, and discontinued. Had to buy complete Ice Bucket assembly.
Washed new Ice Bucket assembly with dish soap and warm water, and let dry. Removed (4) small screws holding Ice Bucket Door assemby to my original Ice Bucket assembly. Reinstalled Ice Bucket Door assembly to new Ice Bucket.
Parts Used:
Auger and Ice Bucket Assembly
  • Steve from Canyon Country, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice maker leeking
opened back panel and replaced valve verry easy
Parts Used:
Dual Inlet Water Valve
  • Wes from Marion, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
The auger in the ice bucket was rusted
Removed 4 screws from the old rusted ice bucket ( they hold the cover on) installed the cover and screws in the new ice bucket and installed the new unit in the freezer .
Parts Used:
Auger and Ice Bucket Assembly
  • Frank from Temecula, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Put the part in and observed water leaking from the ice maker which caused the cup to break
Ordered new Ice Maker from you and fixed the problem completely.
Parts Used:
Ice Dispensing Drive Cup
  • John from Ravenden, AR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
no ice
Followed the video, very simple
Parts Used:
Ice Maker
  • Richard from Las Cruces, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Not dispensing water
I watched the video on the partselect website once and completed the repair. Very easy!
Parts Used:
Dual Inlet Water Valve
  • Anthony from Orlando, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
The ice dispense door flapper was deformed letting warm air into the freezer compartment.
The trim piece covering the opening of the dispenser is the first and most difficult part of the disassembly. Take care when removing this piece that it does not break.
Parts Used:
Dispenser Door Assembly or Flapper
  • David from Kennesaw, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
actuator pad it was broken
just i took off the actuator and replace with the new one in 8 minutes.It was so easy.
Parts Used:
Actuator Pad
  • JULIO from LOS ANGELES, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Would Not Dispence Ice
Watched video on the parts order information page and did the repair. Very helpful made me feel like I could do the repair
Parts Used:
Dispenser Control Board - 2 Slide Switches
  • Richard from Garland, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Frezzer would freeze up, refrigerator stayed cold, solved the problem. Now the refrigerator seems to be running more than usual.
Checked the defroster coil which is located behind the rear panel in the freezer compartment, it was still working. Followed the schematics down to the defrost timer, which is located in the lower front of the refrigerator and tried that. Plugged in the new part and the problem is solved.
Parts Used:
Defrost Timer - 120V 60Hz
  • Henry from West Seneca, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Refrigerator was only dispensing crush ice and not cubes
Solenoid pushing the crushed ice flapper was burned out. Solenoid was easy to find unplug and replace. I used the old piston which simplified things. Now works great
Parts Used:
Ice Dispenser Solenoid Service Kit
  • Charles from Spring, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
ice maker was spewing water into freezer
Ordered this part after i replaced the plastic tubes on the back as the problem persisted. loosen the nuts holding the water inlet lines, remove the cover to the valve. remove the valve and the water inlet line to the the valve. Disconnect the 2 outlets from the valve. 1 outlet to icemaker and other outlet to water cooler (bigger). Connect water inlet and 2 outlets to the new valve, test the water lines. Found the inlet is leaking, removed it and added teflon tape and reconnect it. All is done. Then I left the freezer door open for 3 hours to melt the ice on the wrong places and all is well.
Parts Used:
Dual Inlet Water Valve
  • andy from clearwater, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the ZISB36DXA
451 - 465 of 537
Back to Top