Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
attaching overflow micro switch to new plate
Once i had the dishwasher removed everything went as the instructions indicated except for the overflow switch.I removed the switch from the old bracket which is not required,just install the switch assy. to the new bracket and proceed as instructed. the total repair shouldn't take more than 1 hour if you don't make the mistake i made.I AM VERY SATISFIED WITH PRODUCT. I HAD NEXT DAY DELIVERY AT REGULAR POSTAGE CHARGE.
The motor seized up on my 1990 GE Dishwasher Repair would cost 360. Replacement about 600 I ordered the motor and pump from PartSelect for 137..44 Remover the under counter washer (it‘s very light) and removed the water and drain line and disconnected the power. Turned the washer on it’s top to access the motor and pump and removed the electrical plug in lines, and the clamps holding the pump on to the connections. Replaced it with the new motor and pump, reconnected the electrical plug ins, added an adapter hose part, tightened the original clamps then reconnected the water, drain and electrical connections and reinstalled the washer. All in about an hour, The only glitch was the grounding screw for the ground wire on the motor. The screw was too long to tighten. Substituted the original shorter ground screw from the old motor, and that worked fine. Only used 4 parts from the large assortment of parts supplied. Immediately ran the washer through a cycle, all worked perfectly.
The old pump for this 21 year old dishwasher was leaking. Reviewing the cost of a new dishwasher at the big box stores convinced me replacing the part would be much less money.
I had hoped to be able to do the entire replacement at the floor level through the front panel without moving the dishwasher out of the cabinet. That turned out to be impossible because two of the machine screws holding in the old pump rusted and would not budge. I did however manage to do the replacement by moving the dishwasher only 16 to 18" out of the cabinet so that I could work on more than one side. A word of advice: Once the pump is disconnected get it out of the house as soon as possible. It will continue to leak on your floor otherwise. No point in getting your pants, shirt and tools all wet. The best part of this replacement came when I buttoned the whole thing back-up and ran it. This new pump was significantly less noisy than the old one making it possible to stay in the kitchen and actually have a conversation with someone. (My dog no longer leaves either.) Would I do it again....you bet!
First make sure the dishwaher is off and secure to work on: remove the lower basket, turn the broken spray arm assy counter clockwise, it may be tight, but no tool be need it, screw it all way out, remove it and replace it with your new one by turning clockwise,make sure its tight, no tools need it but basket in place and the dishwasher is ready to go
Old roller wheels were starting to stick due to cracking
1. I pulled off the plastic end caps to the top rack that allows the roller wheels to be pulled out of the aluminum rails. You need to push in the raised edge of the plastic caps so they clear the rail slot in order to remove them. This takes a little bit of finger pressure or you can use a flat-edge screw driver to pop them out. 2. Once this procedure is completed, you simply remove the rack and rollers from both rails and remove the old roller wheels and replace them with the new ones. 3. I used a phillips-head screw driver to tighten up the rail wheels before re-installing the top rack into the rails and then re-inserted the end caps. Pliers are handy to help get the end caps back into the rail slots. 4. I finally used a silcon spray on all of the rolling parts of the top tray assembly for lubrication.
Water stays in the bottom because the solenoid burned out.
It is pretty easy to replace the parts because the new and old parts are identical. I unplugged wire connection, removed the two screws and one small metal piece that fixes the plastic moving part, then put back with new parts. A little bit extra time may needed due to small space in that location, also the small or flexable screw driver is needed.
Disconnected the electrical, water supply and drain. Pulled unit out from under counter, tipped it on its side and replaced the motor/pump unit. tipped it back on its legs put it back under the counter connected the water supply, drain and electrical. All went well. The unit performs as it should. it took about two (2) hours without rushing through it.
Removed original silverware basket from dishwasher rack. Replaced it with new silverware basket. Placed original silverware basket in recycle bin (plastic content). So easy, even my 24 year old son could do it!
Dishwasher was retaining water after completed wash cycle.
Changed check valve and valve flapper. Had to pull dishwasher out of cabinet to get to the backside. Removed check valve and replaced valve from inside dishwasher ( all the way at the back, large nut holds in)but had to remove lower assembly from rear in order to change out the gasket. Removed large black flexible tube and replaced flapper valve. Just be carefull sliding hose back over section containing flapper valve. Fairly easy switch out. Took care of problem.
Shut of water to the built in dishwasher and shot of electric breaker , removed the water line and removed electric hookup at washer. Removed the drain pipe connected to the garbage disposal unit for more darin pipe room when pulling the appliance out from under the counter. Pull out the appliance, and carefully layed it flat on the back. Loosed the 2 connector clamps with a srewdriver from the upper and lower rubber connectors and the small drain rubber connector, used a plier. Loosed the screw on wire hold down pulled the housing pump out of the rubber connectors and used a wire hanger to help support the dangling housing pump unit. Unscrewed the damanged rubber connector using a washcloth for a better grip. , Rescrewed in the new rubber connector. ( Hint- used petrolem vasaline on the rubber connector base for a water tight fit) . Reconnected all , replaced elctric and water line, reconnected the darin pipe to the garabage disposal. Turned water back on. All worked at well.
No Plumer could help me. No one heard of a dishwasher check valve. My dishwasher was an ISA. I was lost until i found the relationship to Kitchenaid. Then sears. Vuela! The valve was there, but unavailable. A few more links, and the term "flapper" came up. Well, my dishwasher check valve HAD a flapper inside. Although a plastic pos, i could unscrew the two halves and see the flapper. A little piece of rubber, about 1" in diameter All suppliers gave me but two choices. One large (size given) one smaller. After years of searching, all I needed was a flapper valve. Not the whole check valve. I found it hear for under $10
Very, very easy. Took about 5 minutes. The end cap was on and working. And the repair company would charge $65 just to come out and look at it. It costs $9.00 to fix it. I am moving on to the refrigerator next. Very satisfied. Shipping is well worth the money. Ray D, Ansonia, CT
Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.
Pulled the basket out the appliance and took what was left of the roller off and replaced them and slid the basket back onto the slide channel into the appliance. Then snapped the end caps on. Almost too simple. Less money than it costs to have the service man ring your door bell.