YMET3800TW1 Washer Dryer Combo - Instructions

I pulled the dispenser cap off the top of the agitator, then removed the water tight cap from inside, then used a socket and extension to remove the bolt and the top portion of the agitator. The cogs and holder easily came out of the agitator, then the black hold down ring was slipped away from the cogs and the cogs then easily were removed and replace with the new ones. The black hold down ring was then slipped back into place to hold the cogs in and the agitator was reassembled. Works perfectly now and only cost $8.95 and three days for shipping.

My way of replacing the pulley was much faster than the parts select video that showed how to replace the belt tension-er pulley. They took off the door, the entire front AND the drum to get to the pulley. I ACCESSED THE PULLEY BY REMOVING THE 4 INCH EXHAUST PIPE, (ONE SCREW) WHICH GAVE MORE THAN ENOUGH OPENING TO REPLACE THE NEARBY PULLEY! I suggest you remake that video

I removed the top agitator cap, pulled out the secondary cap with my bare hands. This exposed the bolt. Next I removed the bolt and lifted the top agitator off. Installed the "dog ears" into the cam kit placed in the new agitator and snapped them back into place. Make sure you keep the cam in place so the dog ears don't slip out while you are trying to reassemble.Next I bolted it down replaced both caps and I'm done. It works perfectly.

I simply watched the video that was on YouTube for this site. It was dead on with my washer and super easy to do. The step by step was just awesome and easy to follow. The repair took just over an hour and I even cleaned the entire inside of this 12 year old washer which was pretty cruddy. The washer now spins great and works like new again. All for about $50. Thanks.

A word to the wise watch the repair video first guys and save an hour or 2 of aggrivation. I saved a couple hundred bucks instead of having the repair guys do it. It was easier than I thought. Machine runs like new again. Thanks Partselect. L.A.B. Rocland, Mass.

Removed the upper sgitster by removing the center bolt to the bottom agitater. Manage to pull the cog housing apartfor inspection. left apart and ordered the new cogs. received the cogs within 30 hours and reassembled the unit and bolted it back to the main agitater. works perfect. great service. Thanks Ed PS Now my 97 year old mother in law can keep washing clothes. Shes happy again.

Remove the sides of the washer, motor ran but nothing moved, closer look found drive coupling broke (10 years and it made of plastic) Order a new part from you, arrived very quickly. Install the part 10 min. later it was running.

I replaced the Cycling thermostat. At first I thought I may have blamed the wrong part because the ohm meter read almost the same for the old and the new part. It took less than a day for the part to come probably because it came from Jacksonville. I haven't guessed how much I saved by not calling a appliance repair.

Got the latch kit, found the correct one, popped it in...dryer works! Thanks....

Removed the cap and the unit that held the cogs or dogs. Replaced and reassembled. Took about 5 minutes.

The repair went great . Thanks for the part ,will be purchasing parts from you now on.

Pop the top of the agitator off, 3/8th socket to remove the bolt holding the entire Agitator assembly, pull straight up to remove the entire agitator assembly, remove agitator dog assembly, pull plastic retainer holding agitator dogs in, replace agitator dogs, replace plastic that holds them and just put the thing back together. If it takes more than ten minutes you must have stopped for a beer break

We followed the step by step video that you had posted for those parts. It is now working wonderfully. The repair man had told us it could not be repaired. Thank you so much for having these do it yourself instructions.

Having read the instructions and watched the tape, I pried out the remaining catch with a flat screwdriver, read about what the color scheme on the parts wasbout and pushed in the correct part. Voila ! Done in probably two minutes.(By an 82 year old woman!)

Followed the video did not need to tilt machine over. Layed on floor it was more comfortable. The most difficult part was putting back on the tension band on top that's because I got a little tired on the food. Thanks for all your help. I bet I saved over $250.00 if a service tech came to fix this. You guys are the best