Models > WWEF3004KWA > Instructions

WWEF3004KWA Westinghouse Range - Instructions

All installation instructions for WWEF3004KWA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the WWEF3004KWA
601-615 of 636
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

wrong temp when baking.

  • Customer: John from Hiawassee GA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
removed back. discovered wrong connector on probe. Cut the connectors off and spliced with small butt connector. Took me longer to find the tools and connector than to do the repair. The wires are very small and require a very small butt connector. Tips by the sales rep and previous customer were helpful. Great service. Will try PartSelect for Cub Cadet and Yamaha OB parts. Thanks. John

My burner would stay on high regardless of where it was set.

  • Customer: Smtella from Wappapello MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
We removed the back of the stove, unscrewed switch from the stove face and unplugged the wires from the old switch. The new switch was universal so I had to follow the numbers by the prong on the old switch to determine which was the correct prong to plug the wires, plugged them in, screwed the switch back to the stove face and replaced the back Viola all fixed.

Bake element burned out/failed .

  • Customer: Ron from Riverside TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Used 1/4 nutdriver unscrewed the old unit from the back of the oven wall pulled out the element, pulled off the blade connectors off the push on terminals, took the new element and pushed on the new connectors screwed the element in place and presto that was it ! Repair time was less than 5 minutes.

Lower heating element bad

  • Customer: LESLIE from CONCRETE WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Very easy repair. Removed oven door, removed two screws holding the element in place, unplugged the wires at each end and installed the new element.

The bottom heating element snapped into several pieces.

  • Customer: Teri from Keller TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I watched the video on your site before I purchased the replacement part, sure that it seemed simple enough to replace. Overall it was smooth and easy, the only difficult part was loosening the screws to remove the old element. On another site someone said to use clothes pins to keep the wires from slipping back inside while you did the replacement, that was a great idea. Thanks for hosting videos showing the repair before a purchase is made, so the purchaser can be sure they can handle the repair themselves!

Burner would get hot, but would not turn down.

  • Customer: Rick from Montpelier IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
To find problem. I turn the power off to range. Removed top back panel. Removed switch and found there was a black spot on white covering of switch. So I order a switch. When it came I turn power off to range. Removed the top panel on back of range. Removed one wire at a time and put it on the new switch. Once all wires were on new switch. I removed old switch and installed new one. I then reinstalled the top back panel and turned the power back on. It is really easy to do. If you are not confident enough. Take a picture of the back of range before removing the panel. Then take a picture of the wires before you remove them.

My oven element burnt out.

  • Customer: Stephanie from Wakonda SD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I ordered the part online using the model number. It came within 5 days. I had watched a video online to see how to do this repair. It was easy. I unplugged the range. I opened the oven door. Use the nut driver to remove the screws in the back of the oven that held the element in place. Once the screws were removed I gently pulled the element forward exposing the wires. I wiggled each fastener from the element. I just clipped on the new element ends to each fastener and screwed it back into the holes in back. Plugged it in and am pre-baking ribs...before I put them on the grill to finish. Yum!

ice maker tray was leaking water from tray.

  • Customer: DALE from HAMBURG PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
i took 3 screws from ice maker,then unpluged from frig.i then transferred cable to new ice maker and installed back into freezer. very simple.

Oven bake element burned out-no heat

  • Customer: Mark from Laurel MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
It is critical that the power be turned off AND the oven unplugged for safety. This should also be included as a big warning note in the element packaging. This repair is extremely unsafe if power is not disconnected. In my case the plug was accessible by removing the warming drawer. Once power is off, simply remove two 1/4" screws with nut driver and pull the element out slightly to access connectors. Disconnect, while not allowing wires to fall back through holes at rear of oven. Connect new element and slide back into place, replace screws. I also replaced a broken warming drawer slide while I was at it, it just snaps into place.

Renter complained about oven not working.

  • Customer: Floyd from Leesville SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After confirming that the renter had broken the timer through frustration I ordered the correct part and fixed the problem.After removing the rear panel it was obvious the timer was broken..just put wires where needed and reinstalled the new clock timer..The oven worked like new..

oven does not heat

  • Customer: DeWitt from Boulder CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Disconnected the heating element from oven box (nutdriver), pulling element outward toward the oven door to expose the element's push-on electrical terminals for voltage measurement. Used paper to insulate terminals from oven box while setting oven to "bake." Determined that electrical power (230 VAC) was present; then switched off oven and double checked the element itself was open circuit by measuring continuity with one terminal disconnected. (Violated all kinds of safety rules!) Temporarily reinstalled the bad element to maintain safe condition while waiting for replacement element. Be careful with delicate push-on terminals to avoid connectors coming off wires.

No heat in oven

  • Customer: Delbert from Auburn WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
When you order make sure and get a new faceplate also. I didn't realize it was glued on .Whne I pealed it off part of the white stayed on the old control,looks bad but works fine.Unplug Range, Take 4 screws off of top panel on back,I left all wires hooked up and removed 4 more screws holding the control panel in place.I rolled it out of the way put the face plate on the new one and screwed it into place. Then took each wire off one at a time and hooked thenm to the new one. Reattatch the back and test it out..You now have a happy woman.

I needed an extra oven rack to bake more at one time.

  • Customer: Sally from Cincinnati OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I just installed the extra rack and re-arranged the existing ones. Works great!

comp board went bad

  • Customer: Brian from King George VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Very easy to do take the computer out. Had it done in about 2 minutes. Very simple use a drill with screw driver tip makes quick work. Plug the board back in button it all up oven works great.

RF burner only had High Heat.

  • Customer: Garner from Sykesville PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug the range, pull the knob off the front. Remove the screws from the cover plate behind the switch and remove the cover plate. Carefully pull one wire at a time off of the old switch noting the markings: "L1," "L2," "H1," etc., as the wire position may be different on the new switch. Put each wire onto the new switch as they are removed from the old one. Let the new switch hang from the wires while removing the 2 Phillips head screws from the front of the old switch and remove the switch. Hold the new one in place, start both screws, & then tighten them. Push the knob on the new switch. Plug the range in and try it. If everything works, install the rear panel and screws. I think that it took me longer to type this than it did to actually do the job.
All Instructions for the WWEF3004KWA
601-615 of 636