Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
mottor starts than stop.
i looked byhind the freezer , the mottor has the relay connected to it.i took out the relay, and i descovery something was loose inside, i decided to take to check out at sears to see if they have in stock that especific relay. they did not have, they could order, that's when i dicided to go ahead and looking for in the internet, good i found PARTSELECT,they had the part and i was very nice attended,they sent in 2 days i had fix my freezer. thanks PARTSELECT. gilmar couto.
1. turn off the refrigerator using the inside temp dial 2. take all food out of the refrigerator door 3. pull up the gasket along the door frame and loosen all the screws starting with the bottom and the sides 4. loosen the screws underneath the gasket on the top of the door (be ready to lower the door frame when you loosen the last screw!) 5. pull the old gasket off the door frame 6. put the door frame on the floor insulation side up 7. lay the new gasket out on the floor and use a blow dryer to heat the new gasket to make it flexible 8. put the new gasket on the frame by fitting the crease of the gasket over the edge of the frame making sure that the magnet side of the new gasket is facing the refrigerator when the frame is re-attached 9. apply RTV Silicone sealant along the entire lip of the gasket (on the insulation side of the frame) and press the gasket to the frame to form a bond ( I got a tube of RTV silicone at Wal-Mart in the automotive dept. near the motor oils) 10. wait 5-10 minutes to let the silicone bond to the frame 11. lift the frame up and re-attach to the door starting with the top middle screw first, the side middle screws next, the bottom middle screw last (you may want to get a second person to help hold the frame while you are attaching these initial screws) 12. go back and re-attach all remaining screws 13. close the refrigerator door and check for a good seal all along the gasket 14. your done!
Note: you may want to close the refrigerator door and block it with a chair to keep in some cold air after you remove the frame to install the new gasket
I put the refrigerator and saw that the fan wasn't working so I change the fan and the problem still the same. I order a timer and thermostat and change them, nothing change so I order the capacitor and when I remove it I saw that the relay swith was burn out so I order a switch and evarything is ok. The problem when the fan broke the compressor overheat and burn the swich. I learn a lot and still saving money over these repair guy.
I basically followed the instructions offered when i searched for the ice maker. It was relatively easy to do, I undid the 2 screws holding the ice maker to the side of the freezer, the was the tricky part, holding a mirror so i could see the slots of the screws. loosened them, disconnected the electrical connection and reversed the process for the install. It took about 25 minutes and i was back making ice.
removed doors and took out screws from hinge and replaced hinge. works great, all costs under $20, applinance store said no parts available only wanted to sell a new appliance, no wonder they are all losing bussiness when they have custmor service like this!
I pulled out the old pieces and poped what I couldn't into the foam insulation behind the support. Then I placed the new piece in the hole and popped the plastic pin to seat the support. bang. the only problem I had was knowing if it was the right part by the picture. The little pin that had to be pushed through kinda threw me.
I removed the plastic cowl in the rear of the freezer to gain access to the fan, took out two screws that secured the brackets holding the fan. Then I separated the coupling wires which had a sort of locking mechanism that was simple to undue. I took out the brackets along with the fan, separated the brackets and removed the screw for the ground wire. Then I simply reversed the process.
Did the obvious. Removed the stick-out cover, then the back of the freezer wall, after taking the bad evaporator fan out. Replaced the old motor with the new one, stuck the fan blades back on, and put the replacement back in place. Checked to see that the new motor and fan, before final hook up, had no issues. That was a success. However, when I put the parts in place, I had some significant vibrations. By taking things apart and re-doing the install, the vibrations went away. However, the final install, even if quiet, did not work. Apparently the condenser was kaput. No cooling after all the adjustments. We gave up and are replacing the fridge.
it was really easy changing the ice maker. the only trouble i had was the wiring. it was very stiff and hard to route. it did not work at first but that was my fault did not have the connector plugged in all the way.since then it works great.
Loosened the 2 screws a little so that it would slide up and off then unplugged the wire harness. Installed the new one in reverse order and works like a champ.
Removed the old and installed the new. Electrical plug/socket made connection easy. Biggest problem is working space in freezer side of a side by side with the fan in the back. If I can do it anyone can.
Wasn't sure if it was the derost timer or the heating element. Since the timer was much cheaper, I bought it and crossed my fingers. My story is like the others. Unplug the refrigerator, snip the old wires, strip back the wire insulation, use the supplied connectors to attach the new defrost timer to the existing wiring. Success! My coils no longer freeze up. Only difficulty is I am a large guy, and fitting my upper body into the freezer was challenging.