WRS26MF5AS2 Westinghouse Refrigerator - Instructions

All instructions included on this site are good. I would add only one thing to them. When removing the 4 water lines from the old unit be sure to pull up on the white rings while you pull down on the water lines. All else is a snap.

I removed the top hinge cover, loosened the hinge so I could remove the door and laid the door on it's side. I removed what was left of the Door Closing Bearing and istalled the new parts. Set the bottom of the door on the lower hinge then postioned and set the top hinge into place and tightened the top hinge and installed the hinge cap.

i was trying to figure it out but eventually it fix it self even when i get the part the problem seems to be fix on its own i unpplug the eletrical cord from the wall for over three hours and plugged back in and after 2 more hours it works so i am confussed dont know what happen i did not change any part so i have one brand new inlet water

It was simple... After paying $280 for a repair man to come out and install some unnecessary part to the fridge when I told him "everything on the Internet points to a thermostat repair." He disagreed, fixed the fridge and said the freezer would work more efficiently now. It didn't, so I bought a new fridge/freezer, put the old one in the basement. I ordered the thermostat (under $20), put it in, and now (knock on wood), works great and I have a beer fridge for the man cave

Very very easy just slip replacement bins back into place. We did receive our order the very next day after ordering, so the parts ordered came very quickly... so thanks for that. Just hope these last longer than the originals did.

Easily installed the new ice-maker. Rec'd the part in three days.

Ordered the replacement bin> It arrived the next day. Tool 3 seconds to pt it in place and all is back to normal. Good service.

The young lady that helped me was fantastic... great product knowledge and affermed the correct and we got it ordered... Fast shippers and the install was easy although there were no instructions to be had... checking the gasket and removing the old one,,, it pressed in place in moments... They are booked marked and will use them the next time...

The gasket arrived in two days as advertised. Removal was easy and did not require any tools. The new gasket was simply pushed into place. It was so simple and easy, I thought more was required. I will definitely use this vendor again !

I watched the step-by-step installation video and followed the instructions therein.

I ordered a freezer upper door bin and received the wrong part. I contacted PartsSelect immediately and they re-shipped the correct part. It was well packaged, I removed the part and paper towel wiped it down and snapped it into the freezer door bin. I highly recommend PartsSelect for their great products and Customer Service. I even add them to my contact numbers in my cell phone, they will be the first I call, when needing a part for any appliance!

I replaced the condenser fan motor, but first I bought a brush to clean the coils. I first unplugged the fridge and took off the back panel. I located the fan motor and noticed how dusty it was back there. All the dust dirt and pet hair can accumulate making the motor work harder and overheat. I cleaned the coils with the coil brush and a shop vac. Once I cleaned it, I started to take off the three screws that held the fan motor suspended,its important that you move the fridge enough so you have adequate room to work. I unplugged the motor and finished removing the screws. When I removed the motor I was upset when I compared it to the motor I was sent because it looked physically different. The motor I removed had a plug that was integrated in the motor, but the one I received had a plug that pigtailed outside the motor. I called PartSelect and told them they sent me the wrong motor. The lady that I spoke with was very friendly and helpful, and after looking up my part # she assured me that it was the right part. Next I had to remove the fan from my old motor, the nut that held the fan on looked like a clip, but it screwed off using open pliers.I removed the fan and put it on the other motor, using the parts supplied. Before I installed the motor I screwed the three screws in and out of the three screws holes to make the screws go in easier during instalation. I installed the fan motor using the three screws supplied, and once it was secure I spun the fan with my finger, making sure the fan spun freely and installed the plug to the fan. I then plugged in the fridge to make sure the fan was working,and replaced the back panel. Hope this helps you out, good luck.

quick to repair great instuctions

I was unsure how I was going to be able to make this repair. However, it was so easy I have planned to order other items to make the repairs myself. I am a rental manager at a condominium complex and I think my homeowners will be very happy when they see how much money we can save them by our office doing the repairs.

Removed the drawer rails from the shelf, installed the new ones. Viola!