| |
49 of 54 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerJonathan from Universal City TX
Water actuator broke
If you think you probably can't do this, you're like me... but you just had to try because you needed the part anyway right? This really was quite simple, a lot easier than it sounds from the description and saved me probably $75 I'd have had to pay a tech to do it. Just unplug fridge, yank that water spill tray out, yes yank, it's a bit hard to do that if you've not done it before. After that remove the 3 phillips head screws you just gained access to. Lift panel frame up then out. Disconnect wire harness plug and set that frame aside. Take out next screws exposed to free the unit. Tilt unit out and remove the two little screws and shims holding actuator in place. Remove broken one. Put new one in. Reverse all actions taken thus far. Plug fridge back in and have a drink of water like nothing ever happened. : ) You can do this!
|
11 of 11 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerKathleen from Golden CO
Support rails holding meat tray drawer broke.
I removed the drawer from the support rails and placed it aside. I then removed the entire shelf that the rails were attached to. Each rail contained one (1) screw. I removed the screw, slid the support rails back approximately a 1/4 inch and they popped out. I replaced with the new rails, sliding them into place in reverse of how I removed the damaged ones & attached with the screw. I cleaned the shelf off and placed it back in the refrigerator, and placed the meat drawer onto the new rails. It actually took longer to clean the shelf than perform the repair.
|
8 of 9 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerMark from Colorado Springs CO
Meat drawer and support rails broken
I pulled the shelf unit out and removed the screw that held in each side. The old rails removed easily and the new ones installed just as easily. I put the shelf back in and slid the new meat drawer in and it was done - much to the delight of my wife. Parts Select has a great website. It was my first time and I read one of these with the exact problem I was having. I ordered the parts, which came quickly. Everything easy and worked great! I'm a happy customer.
|
6 of 6 people found this instruction helpful
Parts Used
-
- Meat Drawer Rail - Right Side
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
Tools
CustomerKarl from Bellaire TX
Support rail broke
I recieved the part within 48 hours. I snapped the part in place and I was done in seconds.
|
5 of 5 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDavid from Mogadore OH
The meat keeper drawer kept falling
Backed one screw off each side of the shelf brackets, snapped old ones out, snapped new ones in and replaced the screw. Spend more time taking food off the shelf than it did to make the repair
|
5 of 6 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver
CustomerKristen from Payson UT
Too of the rail supports inside the fridge were broken
First I removed two screws per rail and removed the old rails. I replaced with the new rails and used a nutdriver to secure in place. This was extremely easy and I fell like my fridge is brand new again.
You can do it!!!
|
4 of 4 people found this instruction helpful
Parts Used
-
- Meat Drawer Rail - Right Side
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerBetty from Hot Springs AR
Support rail had broken lower slide
Could have done it with my eyes closed! Removed shelf and drawer, then removed broken support rail. Removed screw from broken rail and put the new, two piece rail together using that screw. Snapped rail back onto wall...returned shelf to fridge...returned drawer to fridge...returned myself to sanity! Yee Haw Easier than installing it was ORDERING IT. I was amazed by the ease of that process. Your ordering site is incredibly easy. By the way...I am a blonde and for blondes everywhere...Look at what I could do :)
|
3 of 4 people found this instruction helpful
Parts Used
-
- Meat Drawer Rail - Right Side
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerTina from Baroda MI
My son pulled on the meat pan & cracked the right support.
The old support just unscrewed & then the new one screwed right on with two screws.
|
3 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerDoreen from Ormond Beach FL
Plastic guide rail broke
A plastic guide rail broke after the meat keeper drawer was left open and the refrigerator door was shut on the drawer, this has happened a few times over the last 6 years. We chose to change out both rails at the same time. We removed the meatkeeper drawer, then the shelf above as the rails are attached to the shelf. We removed the rails (one screw on each side. When the new rails came in, we replaced them with the screws. Super easy!
|
2 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerTed from Hudson NH
The side rails on both sides of the drawer that holds the lunch meats were broken.
Pulled out the drawer, unscrewed the old rails, screwed inthe new rails. It was that simple. The hardest part of the job was removing the food items off of the shelf.
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerCurtis from Palm Desert CA
Meat drawer needed new tracks
Had to replace both sides tracks; the plastic is thin and gets alot of use. Had these done in minutes, one screw out on each side allows the tracks to be removed.
Best part of the repair is the new clean shelves and drawers. How can you do this repair without cleaning everything?
Nice quick service from PartSelect, and the right parts!
|
2 of 3 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerBurnell from Reno NV
Install deli drawer
removed refrig shelf, attached side brackets with one screw( screws were not included in shipment) on each side; reinstalled shelf, slid in the new deli drawer and we are very happy.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customerbrenda from hillsboro MO
Plastic drawer slide was broken
First I watched the video that provided - extremely helpful - thank you- when the part arrived I removed the drawer and shelf - unscrewed the screw- pushed the slide catches to one side and removed - then I screwed new slide on - pushed to lock in the catches and DONE! That simple - EASY PEESEY!! THANKS SO MUCH FOR VIDEO AND SUPER FAST NEXT DAY SERVICE - AMAZING HOW FAST!! WILL USE ANYTIME I NEED PART AND HIGHLY RECOMMEND YOUR SITE! TIME- 5 MINUTES TOPS!
|
2 of 4 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
ToolsScrew drivers
CustomerChristy from Bountiful UT
Actuator broken
The first thing I did was unplug the refrigerator for safety's sake. Then I made a mistake. I peeled off the module cover label. All I needed to do was pry the drip tray off to reveal the screw that holds the Module Cover in place. I used my fingernails to get under the botton edge of the tray then lifted it gently off. Then I unscrewed the Module Cover pulled it away from the freezer door and unplugged the electrical connection so I could set the Module Cover out of the way. I removed the broken piece of the original Acutator by unscrewing two tiny bolts from two tiny plates. That's where the tweezers came in. As soon as I took those little bolts out, the plates fell into a place where I could barely see them, let alone get into with my fingers. Once all the tiny pieces had been retrieved and put somewhere safe, I inserted the new Actuator up through the opening. The Actuator has an arm that sticks up and pushes against a spring to open the water flow. You'll want to make sure that arm is in front of the spring. The tricky task of screwing those two tiny plates back in took a while and a little swearing, since they now had pressure against them from the spring, but I was able to get it done with the help of a magnetized screwdriver. Then it was just a matter of plugging the electric cord back into the Module Cover and screwing the cover back into place, replacing the drip tray and sticking the label back on. The repair wasn't difficult it was just an extremely small space in which to work. The Drawer Support Rail and Refrigerator Door Shelf Bin popped in in about 30 seconds.
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerVeronica from Joppa MD
Age and 3 kids pulled the deli drawer down, breaking the tracks
It took me longer to empty the drawer then to attach the new tracks and reinstall the new drawer. My husband was surprised when I did it while cooking dinner. Saved me at least $75 for an appliance repair visit.
|