WRS23W0AQ6 Westinghouse Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Crisper support pins were quite tricky to secure
The old pins have to be completely dislodged (preferably with an awl) before placing the new crisper support. The new pin of the support should be driven easily into the hole on the refrigerator´s wall with a conventional hammer (carpenter type). If you find resistance while hammering on the pin, do not continue. This probably means that the old pin is still inside the hole and does not allow the new pin to go in.
Parts Used:
-
JOSE from Miami, FL
-
Difficulty Level:Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Ice maker
I needed one with the adapter. I installed it and there was ice in the tray the next morning...no problem
Parts Used:
-
Bart from Stillwater, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Crisper supports were broken
Drove pins all the way thru supports & then pryed support off. Tapped new supports in place. Watch the vidio on installing new supports. I probably wouldn't have been able to get the supports off without the trick I learned to just knock them on thru. Took all of 5 minutes to replace 4 supports.
Parts Used:
-
Fredey from Andrews, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original shelf broken
Replacement took about 10 seconds, just put it onto the holding brackets, pressed down and presto...DONE!
Parts Used:
-
William from Longs, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fridge door would not close automatically
I removed the door and replaced the broken hinge bearing with the new part and the door works great!
Parts Used:
-
Michael from Campton Hills, IL
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Socket set
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker quit workin
-
Robert from Park Forest, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
plastic door cam broke
it was a simple fix, all i had to do was remove 3 small bolts from top of door, set door aside remove 1 screw that holds door cam in place, install new door cam.hole job took about 15 minute's.
Parts Used:
-
DAVID from HANCEVILLE, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door made a clicking sound when opened...
Couldn't have been an easier. Removed the screw/nuts from the top of the fridge door that held the door in place and removed the door. Unscrewed the holder at the bottom, replaced both parts and put the door back together. It took me longer to get everything out of the fridge door than to replace the parts. EASY AS COULD BE!!!
Parts Used:
-
Kristopher from Branchport, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Missing to shelves
-
Kendall from Brandon, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Made A Loud Clicking Noise When Opening
Took the door off,as per instructions,pulled the worn bottom bearing out, pushed new in and replaced door. The job was very simple and took about ten minutes. Also I received the part in two days after ording
Parts Used:
-
DONALD from CASTALIA, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ice maker did not work
-
shelton from virginia beach, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Icemaker Quit Making Ice
I watched the video and did the same thing on mine and now it is working fine
Parts Used:
-
ROBERT from JACKSONVILLE, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
closure bearing cracked in half.
Simply removed two screws from top hinge and lifted door off bottom hinge. Next leaned door over and removed broken portion of bearing. Finally reinstalled door and works like a charm. Thanks too this site painless repair. Oh ya part is a perfect fit.
Thanks Clay
P.S. Would recommend to a friend. Note shipping WOW. Please consider using US Mail. Shipping more than part. OUCH.
Thanks Clay
P.S. Would recommend to a friend. Note shipping WOW. Please consider using US Mail. Shipping more than part. OUCH.
Parts Used:
-
Clay from minot, ND
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Cam On Bottom Of Right Door
1-Remove upper plate with phillips screw driver (6) screws 2- remove upper hinge plate with ratchet and socket (2) bolts 3- lift door off bottom cam, lay door flat on floor. 4- Remove broken cam on lower part of door, just pull out. 5- Install new cam in bottom of door 6- raise door up, set on cam, reinstall top bolts and screws 7- p. S. Make sure you trace top hinge location with a pencil before removal, so installation has proper location.
Parts Used:
-
David from Laquinta, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Closure/hinge bearing broke
Unscrewed top part of door,put it down and replaced hinge bearing,apply some grease,put door back and done very easy do it yourself.
Parts Used:
-
Eduardo from Fountain Valley, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!