WRS23MF5AST Crosley Refrigerator - Instructions

The old pins have to be completely dislodged (preferably with an awl) before placing the new crisper support. The new pin of the support should be driven easily into the hole on the refrigerator´s wall with a conventional hammer (carpenter type). If you find resistance while hammering on the pin, do not continue. This probably means that the old pin is still inside the hole and does not allow the new pin to go in.

Drove pins all the way thru supports & then pryed support off. Tapped new supports in place. Watch the vidio on installing new supports. I probably wouldn't have been able to get the supports off without the trick I learned to just knock them on thru. Took all of 5 minutes to replace 4 supports.

Replacement took about 10 seconds, just put it onto the holding brackets, pressed down and presto...DONE!

I basically took the two shelves and in stalled them.

it was a simple fix, all i had to do was remove 3 small bolts from top of door, set door aside remove 1 screw that holds door cam in place, install new door cam.hole job took about 15 minute's.

Ordered the part from PartSelect. Estimated time for slow delivery seven days. I got it in three. Removed the cover from the water and ice maker dispenser arena held on by three screes. I had to use an easy out on one rusted scree. Disconnected the wiring to the switches and lat the Circuit Board come forward by removing three small screws. Using tweezers to catch the screws, I removed two small screws holding the broken actuator and put the new one in its place making sure the spring was properly located and the ice maker swivel was under the hold-down strip along with the new actuator. I reassembled the door cover and got a drink of cold water. By the way, always unplug the refrigerator because that area is hot. Dr Robert E McGinnis author of In Search Of Paradise and many other fine books found on Amazon.

Watched the video and read some comments and from that it was easy

Due to the nature of the support deisign and installation which was unusual I watched the video on how to extract the old broken support and install the new one, odering the new part was simple as the view privided in the parts section was specific and and easy choice to make, cost was very minimal and I received it the next day due to my being in close proximity to the shipping point, thank you and my crisper is very happy and so am I.

The part was simple find on the website. Ordered part. But the wrong part was sent. I called them and they promptly refunded my money. Reordered the right part. And once received it took only 5 mins. Thanks to video on website. They saved me approx. 100.00. I tell all my friends about the website. The best site bar none. Now if they could do this for cars!!! I give partselect.com 5 stars.

Have not really done the repair yet( frig is still to full of Thanksgiving leftovers) but I am sure that with the video that was provided by this site the job will be very simple. Many thanks to the person who put the video together.
John Donnelly

I read other comments and most suggested the fix is less than five minutes and a couple tricks (push the remaining piece into the frig if you can't pull out with pliers)and I did exactly that. Parts came in 2 days, repair took 5 minutes - it took longer to open the package. My wife thinks I'm a star!

Pried the broken support insert out with a screw driver and pulled it out with pliers, then inserted the new and pressed it in and Presto the drawer now works good again.

I removed the door actuated light switch with my index finger and thumb on my right hand. I then removed the two wires from the switch. I noticed that the new switch had different look to it,I think Frigidaire must have had a problem with the original design of the switch. Reassembly was just replacing the two wires and putting the new switch in place, and no more door closing problem.

Punch out center of old support, then pull it out. Insert new suppport, insert center and tap flat with hammer. All done!

Very easy repair, instruction were clear and easy to follow