WRS23MF5ASD Westinghouse Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
water leaking fron frig
Watched the video and read some comments and from that it was easy
Parts Used:
-
Stephen from Annandale, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door shelf bin broke a tab holding it in the door.
-
Alan from Petaluma, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Right side drawer track broke
Followed the video instructions and it works like a charm! To top it off, the part got to my house the day after I ordered it! Fantastic service!
Parts Used:
-
Ernie from Campbell, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The old support cracked and the drawer dropped when pulled out
1) Viewed the video 2) Got a screw driver 3) Removed the shelf/bracket assembly 4) Removed the old support 5) Reassembled and put back in place. It took longer to clean the dirty shelf than to fix the support. Very easy.
Parts Used:
-
Scott from Dunedin, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The ice cube tray was leaking water on the cubes
1-Unpluged the refrigerator 2- removed ice cube tray and some food( Placed in cooler )3- unscrewed the two screws holding the old unit lowering it and unplugged it. 4- Had to loosen the cooling coil to get to the pass through hole in the back and pulled the old wire out. Connected the wire adaptor to the old connectorand to the new ice maker. At this point I couldn`t pass the new plug through the back so I strapped it out of the way and installed the new ice maker using the two screws from the old one. Adjusted the fill adjustment and turned it on. Cubes in about 4 hours.
Parts Used:
-
James from Circleville, OH
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken valve, water puddle on the floor
removal of the old valve to identify the problem took the most time. Once the new valve came it it was easy. NOTE: the old one had threaded connectors, and the new one is press/fit so the ends of the tubing need to be cut. The color coding and size matching are great.
Parts Used:
-
Robert from Petoskey, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Wrench (Adjustable)
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The shelf bin was broken
Just replaced the shelf bins and it was very easy and quick. The delivery was quick as well.Thanks
Parts Used:
-
Thomas from Columbus, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Crisper support pins were quite tricky to secure
The old pins have to be completely dislodged (preferably with an awl) before placing the new crisper support. The new pin of the support should be driven easily into the hole on the refrigerator´s wall with a conventional hammer (carpenter type). If you find resistance while hammering on the pin, do not continue. This probably means that the old pin is still inside the hole and does not allow the new pin to go in.
Parts Used:
-
JOSE from Miami, FL
-
Difficulty Level:Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would not dispense ice
I replaced the entire dispenser. I decided it would probably be cheaper in the long run than replacing parts, thus lasting much longer. One thing I would like to comment regarding Part Select is that in all my years of ordering I have never recieved delivery any faster. I ordered one morning and part was delivered the next.
Parts Used:
-
Dwain from Stamford, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken tracks
I just watched the online video and then did.
Parts Used:
-
sam from Billings, MT
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Icemaker Quit Making Ice
I watched the video and did the same thing on mine and now it is working fine
Parts Used:
-
ROBERT from JACKSONVILLE, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Crisper cover support was partly sheared
I followed the excellent directions in the video linked to the email from PartSelect. The installation was quick and easy. I rated the whole operation "a bit difficult" because, if I had seen the video before I removed the old part, I would have known that you tap the support's center rod gently INTO the wall instead of wrestling it violently OFF the wall.
Parts Used:
-
Neil from Lilburn, GA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ice maker did not work
-
shelton from virginia beach, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Getting the light socket to snap back in properly
-
Robert from HELENA, AL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken shelf support
-
Jerome from Hendersonville, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!