Models > WGF354BJDA > Instructions

WGF354BJDA Westinghouse Range - Instructions

All Instructions for the WGF354BJDA
301 - 315 of 378
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken Drawer Glides
Just like the helpful Video. Thanks.
Parts Used:
Rear Drawer Glide Front Drawer Glide
  • Rob from Ballwin, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Igniter was past-due for a change-out!
Just opened up the oven and went to work. Really easy repair. Removed floor of oven with two thumb screws. Removed flame diverter plate from burner with one screw. Removed igniter with two screws. Marked top wire, then untwisted old wire nuts to remove the old igniter. Replaced with new igniter and used enclosed new wire nuts. Reassembly was simply the reverse of above. Only issue - I needed longer arms to comfortably reach back into the oven!
Parts Used:
Flat Style Oven Igniter
  • Kevin P. from Chanute, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Front glider ( plastic) on bottom oven drawer was proken.
I took the new plastic glider out of the bag and it took me about 2 minutes to fix the drawer!!! EASY!!!!! Thanks. carol
Parts Used:
Front Drawer Glide
  • CAROL from salt Lake City, UT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
oven not heating
Oven ignitor glowing but no flame . Tested ignitor w/ ohm meter reading 2.5ohms , should be 3.3 or higher to allow gas flow . Ordered new ignitor , replaces and jackpot !! Oven now fires and heats like new . Thanks for part . Cost , $50 instead of $150 .
Parts Used:
Flat Style Oven Igniter
  • Mickey A from Linden, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken Knob
took the new one out of the package and put it on. Took about 5 seconds.
Parts Used:
Burner Knob
  • Bill from Smithville, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The Ignitor had a brunt spot in the center.
I use a 1/4 in. socket and and ratchet to remove 2 screws and removed cover to get to sheild to unplug the two wire plug . Then used needle nose to remove two conectors from the gas valve.
Parts Used:
Flat Style Oven Igniter
  • Homer from Dayton, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Would not light.
Removed oven racks. Removed oven bottom and flame diverter. removed two screws and cut wires. Spliced new wires and reassembled.
Parts Used:
Flat Style Oven Igniter
  • John from Munster, IN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
ice maker tray was leaking water from tray.
i took 3 screws from ice maker,then unpluged from frig.i then transferred cable to new ice maker and installed back into freezer. very simple.
Parts Used:
Rear Drawer Glide Front Drawer Glide
  • DALE from HAMBURG, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
I needed an extra oven rack to bake more at one time.
I just installed the extra rack and re-arranged the existing ones. Works great!
Parts Used:
Oven Rack
  • Sally from Cincinnati, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The front drawer clip was broken
I took the drawer completely out and installed the new clip just like the video instructed. All went very well with no problems. The drawer works like new. I am glad that I was able to find the part on this site. Thank you so much. I will be using this site in the future.
Parts Used:
Front Drawer Glide
  • Clarence from Colorado Springs, CO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Igniter electrode broke
The three bolts that held the burner busted off when tring to loosen. I drilled out the old studs and replaced with self tapping screws.
Parts Used:
Surface Burner Igniter Electrode
  • Robert from Weidman, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Didn't have back slides
Very easy. Dont know why I didn't do this earlier.
Parts Used:
Rear Drawer Glide
  • Susan from Diamond, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broken Front Drawer Glide
Snapped in the new replacement part and intalled stove drawer in less then two minutes.
Parts Used:
Front Drawer Glide
  • Larry from Dunedin, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The drawer on the bottom of the stove would not close properly. When I opened it, it would fall on the floor.None of the parts stores around here knew what I was talking about and couldn't supply any parts.
I searched the internet for help, that lead me to your site. I typed in the make and model. Within seconds some drawings appeared, showing the part I needed. I watched your video on making the repair. You make it so easy. I ordered the parts you recommended. They arrived in just a couple of days. I went back to your site to take another look at your video and I was ready. In just minutes, I had the drawer out, installed the new guides. The one side, the guide was completely gone, so I could snap in the new2 guide as you recommended. The other side, the guide was broken off and I had to use a needle nose pliers to get it out. Then snaped in the new guide. Re-installed the drawer with all the goodies, wax paper, tin-foil, baggies etc. Closaed t6he drawer and everything lined up perfectly. Thanks to you I've got a drawer that works again aqnd I got it done before my husband got home from work. Funny thing, he hasn't complained or asked me about the drawer. I guess that will be our little secret....Thanks Julie
Parts Used:
Rear Drawer Glide
  • Jewell from Port Charlotte, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Range drawer wouldn't close properly
Removed the drawer, simply snapped the rear drawer glide in the punch-out by hand, replaced the drawer. Works well
Parts Used:
Rear Drawer Glide
  • Kenneth from Vancouver, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WGF354BJDA
301 - 315 of 378
Back to Top