WGD9500TW2 Whirlpool Dryer - Instructions

Had to unstack the unit took it apart and replace the rollers,Belt and Idler Pulley It was the pulley making the noise but I had it a part and for the cost I replace the rollers and the Belt the Job was easy The Washer and Dryer are Great we run about 2 Loads a Day

went on-line to research the problem. found the site and listed the issue. agreed with the probability and ordered the part. it came in a few days. After I ordered the part I watched the short instructional video that was available from the site. the repair took about 10 minutes to pull out the dryer, remove the back, take off the old part and put on the new part - put the back on plugged it in and push it back then turned it on. DONE

Checked motor and other components and found Thermal Fuse did not check out allowing voltage to motor. Replaced Thermal Fuse and Dryer worked

the only thing i do around the house is changing the light bulb, so when our dryer was not working and was about 5 years old, i was told it cost too much to repair and i am better of to get a new one so watched few clips on you tube and ordered the parts from partselect which came with instruction, i could not believe it spend about $100.00 and my dryer is working better than before. bottom line if i can do this anyone can.

I watched the video and after that made the repair, it was very easy and the video was a really big help. From start to finish it took me no longer than 10 minutes.

After removing the back & top of the dryer,I determined the noise was coming the idler pulley.I went online w/ model # & found Partselect.com.I ordered the dryer repair kit (at my door in 3 days) which included all the rollers,idler pulley, belt & hardware.It was an easy job to do even tho instructions were for top control panel model (mine is a whirlpool duet- front control) I did try using silicone lubricant on idler pulley, which worked to quiet dryer for a couple days so my wife could use it while I was waing for parts.Two thumbs up to Partselect.com,I will be purchasing all my appliance repair parts from them..I own all whirlpool stainless steel appliances that have been very reliable,but it's nice to know I have Partselect to fix problems as needed.

self...right part thank you

ILove your service. The part came in 3 days. Best parts service I have ever found. I was told by the dealer it would take 2 weeks to come in.

Got parts in 2 days, fast and easy repair.

Took the back off pulled the thermal fuse off placed the new one in and put the back of hte dryer back on

Thank you for your part service. It saved me about $ 200.00 dollars by Sears not coming out to repair a simple problem.

after watching the instuctional installation video, it real took about 25 to 30 mins to install the new belt. The video was perfact and made the installation so easy..

I have a whirlpool gas dryer. My dryer all of a sudden would not heat up. I diagnosed the problem and discovered that it would light (using the peep hole in the front) when the dryer was cold, but once warm, the flame would go out. I bought a cheap multimeter and tested all the themostats on the back of the unit after removing the back panel. All the thermomstats checked out except the cycling thermostat which should no signal through one of the connections (purple wires). I ordered a new thermo and replaced the old one but it didn't fix the problem. Seems that there isn't a current between the purple connections.... Since the flame did light when the unit was cold I figured it wasn't the ignitor so it was either the flame sensor or the coils. I took the top and front panels off (alot easier than I thought; see videos) and checked the flame sensor with my multimeter. It was fine. Only thing left was the coils, so I ordered a set. IF YOU NEED COILS, SAVE YOURSELF MONEY AND ORDER THE PAIR. YOU GET BOTH COILS FOR < HALF THE PRICE IF ORDERING INDIVIDUALLY. Replacing the coils was rather easy. You will need to prop up the drum with something to keep it from impeding your screwdriver. A stubby philips really helped here. Also, since the gas valves are closed when there is no power, there is no need to disconnect the gas line and fuss about a gas leak (This really saved time). Once the two screws for the coil plate were out of the way, the coils simply slide off the valves and unplug easily. NOTE: Make sure you line up the one new coil with plate when you put it back together. It has a little tab that fits into the plate. All-in-all it took about 30-60 minutes to do. If I were to do it again it would probably take 15 minutes. Pretty easy job for a do-it-yourselfer with only basic tools.

removed back cover and with unit unplugged, removed one wire from each device (thermal fuses and switches) and measured with multimeter. Found thermal fuse open. Removed and looked up and ordered part. Installed fuse and buttoned er up and all good. Hardest part was putting the exhaust hose back on the floor outlet!

Took off front bottom panel reached in removed part that was very dusty. Put in new part. Cleaned out lint inside dryer. Works like a charm.