WGD9500TW2 Whirlpool Dryer - Instructions

Dont believe that '1.8 days average delivery' time. if you need to parts in days, get them delivered overnight. Otherwise it was very easy to seals, rollers and belt. Only advise is on the seals. you might want to sort of stretch them out a bit so they are easier to slip on because once you have the glue on there it is harder (and messy) to be stretching them on

I watched your YouTube video about trouble shooting dryers, and found that the problem was my thermal fuse was out. My exact model of dryer was used in the video. I ordered the part and replaced it following the instructions on YouTube. Since the video was so helpful, I decided to order my part from your company

Most of the time was spent just getting behind the dryer and removing the back panel. It was also a great time to vacuum the area. If you're not working in tight quarters, this repair is really easy. The fuse is not hidden and requires no tools to install (only a wrench to remove the back panel). It started working right away & the part cost significantly less than a service call (about nine bucks + shipping).

Got the latch kit, found the correct one, popped it in...dryer works! Thanks....

The kit turned out to be missing a 7.40" 4" diameter vent that was needed so ending having to get my plumber to use what was there with a "cut and paste" job - took him over an hour. He did say that had the right piece been there, it would have been easy.

The repair went great . Thanks for the part ,will be purchasing parts from you now on.

Used video of PartSelect guy on YouTube to diagnose bad thermal fuse with multimeter. Removed back panel of dryer with nutdriver, removed thermal fuse, found no conductance across terminals. Ordered new part. (It arrived very quickly!) Put in new thermal fuse, replaced back panel. Shortened flexible vent tube so there would be fewer bends. Dryer works now.

Remove the two screws holding the door and lift straight up. Remove the two screws on oppostie side. Face can now be removed by pulling straight out at the top, then lifting face up off of tabs at the bottom. The two coils are at the bottom, held in by a retaining bracket. Remove the screws that hold the bracket. Replace the coils by unplugged their wires. That's it!

Having read the instructions and watched the tape, I pried out the remaining catch with a flat screwdriver, read about what the color scheme on the parts wasbout and pushed in the correct part. Voila ! Done in probably two minutes.(By an 82 year old woman!)

It could not have been easier, thanks to the video displayed when I ordered the part. It was as easy as removing the back of the dryer, taking out the old fuse and putting in a new old. I have NO repair experience, so little I had to borrow the nutdriver from the maintance man at work. I was more then a little leary to try this repair on my own, but decided it was worth all the money I would save not having to call a repair man for my dryer. Sure glad I did I will continue to attempt more repairs on my own.

i replaced the two sensors in the heating element which were very clear in your diagram and it worked perfectly

Checked voltage coming into unit, good. Checked schematic and traced the voltage through the safeties and interlocks. Found the problem at the thermal link. Isolated unit from all voltage sources. Removed part and ohmed the resistance. Found it open. Ordered new link and it arrived before schedule. Replaced and connected wiring, returned power and tested. Worked great! Very easy to find and repair!

changed fuse,radiant flame sensor. no help. bought a new dryer. i don't think the gas valuve was opening.everything seemed to be working properly,just no gas.

Replacing the filter was easy - the new filtes's seal seems much more secure. The new one works much better than the old one.

Got online with parts select, easily found the parts needed and ordered them. They arrived very quickly. The repair itself took all of 5 minutes and now the dryer door stays shut like it is supposed to. Only complaint is shipping was more than the parts but then again, I didn't waste a lot of time running all over town looking for what I needed. So, in the long run I saved money , especially when compared to a calling someone else to fix it.(big bucks for even the most minor service call as you all know).