WFW9200SQ02 Whirlpool Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Front seal leaked
-
Ramon from Houston, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
9 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
baffle in tub fasteners broke, baffle disconnected from tub
-
Carl from Patterson, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
6 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Baffle in washer tub broke off
-
MIKE from BENBROOK, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
6 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Tub was filling with water while washer was not in use
Shut off water supply, unplug washer. Remove screws on fir the top of washer, remove supply lines for water, lift top of washer off, unclip wires going into outlet value, reclip wires into new part, put parts back into place, secure lid and hoses, turned water supple back on plug in washer and put washer back into place, there you go. Oh, one more thing, make sure you check for leaks prior to hut washer back into place. Easy as pie
Parts Used:
-
Wanda from PIKEVILLE, KY
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would not start reliably.
Followed the video on the website. Very easy to replace the part and it fixed the problem. The trickiest part was reinstalling the ring that holds the rubber gasket in place.
Parts Used:
-
Andrew from ROCKVILLE, MD
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would not drain.
Removed three screws holding the cover, then one screw holding the pump assembly in place. After unplugging the power, it took two minutes to remove the clamp-rings from the hoses. The reverse was equally idiot-proof! But THIS "idiot" had 10-thumbs which added to the time to replace the lock rings! Added an extra 5 minutes at most! _grin_
Parts Used:
-
Mike from Virginia Beach, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The water didn't drain, so the drum wouldn't spin
I took off the cover, removed one screw. Removed two hoses and the electrical connector. It only 5 minutes to replace the old pump with the new one.
Parts Used:
-
Jill from New Rochelle, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water leaking into drum when machine shut off
Shut off water. Unplug electric. Remove top panel. Unhook hoses. Unhook tubing unplug solenoid. Use torx to remove part. Reverse steps to install new part. Replace top panel. Hook up water & electric.
Parts Used:
-
Robert from PALM BCH GDNS, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
baffle connectors worn off
-
richard from chetek, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer not drain or spin
it was a really easy fix. unclamped the 2 hoses and took out screw, removed water pump. Connected two hoses back and set in place then screwed in locking screw. could not have been any easier.
Parts Used:
-
LAURA from SPARTA, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
6 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drum was out of balance
Easy fix,
I remove the front lower panel and the shocks where right in front of you , with a little twist with an adjustable wrench the cam right off . I removed and the replaced and it the same when you remove the back panel.
P.S when installing the shocks start by connecting to the bottom and then connect to the drum it will make it lot easier.
Good luck on your repair
I remove the front lower panel and the shocks where right in front of you , with a little twist with an adjustable wrench the cam right off . I removed and the replaced and it the same when you remove the back panel.
P.S when installing the shocks start by connecting to the bottom and then connect to the drum it will make it lot easier.
Good luck on your repair
Parts Used:
-
wilfredo vega from STRATFORD, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Wrench (Adjustable)
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door was not closing properly, broken swivel arm under hinge.
removed door from washer, set flat on table and just loosen up the screws all around, removed old hinge and replaced with new hinge, very easy. back to washing clothes.
Parts Used:
-
Gustavo from YOUNGSTOWN, OH
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking water inlet hoses.
-
Helen from NASHUA, NH
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Multiple water leaks, all rubber parts are chewed up from a mouse 1/
1/4 inch nutdriver, took the top and the front panel of and renew all rubber parts / hoses. It looks less than 1 hours. All parts like factory quality, everything fits perfect.
Parts Used:
-
Tom from SAN MARCOS, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pump not draining the water out.
First I made sure the washer was unplugged from the outlet and I took out 3 screws that held the front panel and removed it to get access to the pump.
I disconnected the electrical plug to the pump and there were 3 phillips head screws that held the pump in place that needed to removed. Pulled out the old pump and slide the new one in it's place with no prorblems. Tighten the 3 screws on and plugged it back in and away we went washing clothes again.
I disconnected the electrical plug to the pump and there were 3 phillips head screws that held the pump in place that needed to removed. Pulled out the old pump and slide the new one in it's place with no prorblems. Tighten the 3 screws on and plugged it back in and away we went washing clothes again.
Parts Used:
-
Martin from Kotzebue, AK
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!