Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TEF351EWC > Instructions

TEF351EWC Tappan Range - Instructions

All installation instructions for TEF351EWC parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TEF351EWC
91-105 of 516
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bake element broken

  • Customer: Richard from Campbell, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 1 of 1 people found this instruction helpful
Removed screws. Tried to pull out old element but spade lugs on old element were bent at ninety degree angle. Once I figured that out I was able to manouver the old element out with the attached wires. Had to be carfull that the loose wires did not slip back ijn through the hole. Reaching in over the oven door was a but diffcult, but all-in-all the jobe was done in a few minutes.

bake element burned up

  • Customer: charles from cartersville, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
removed two screws pulled element out about four to five inches attached wire to new element screwed back in less than ten minutes done

Baking element burned out

  • Customer: Richard from Aiken, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
The element went out on a Wednesday. We ordered the part the next day. We received it the following Tuesday (Mon. was a holiday). My 16 yr. old son replaced the part within 15 minutes. It was a piece of cake-actually it was a pizza!!
First and foremost we turned off the breaker, a very important thing to remember!! Then he removed the two screws that hold the element in place. He then pulled the element out about 3 inches and disconnected the two wires...and reconnected the new ones and put screws back in. Voila!! Ours was stillll under warranty, but we would have had to pay the service call and labor costs. Our do it yourself was much cheaper and faster!!

Oven would broil but wouldn't bake

  • Customer: Chris from Blacksburg, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. connected the new element, reassembled and SHAZAM. It worked. I am not good with electrical circuit testing etc. even though I know it must be easy so after reading many stories here, I decided to start by replacing just the element and see if I got lucky. I did. No need to call expensive repairman.

oven wouldn't heat

  • Customer: Michael from Goddard, KS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
using a nut driver I removed to two screws that were holding the element in place. Then simply disconnected each wire. Removed the old element and plug the new wires onto the new element. Reinstalled the two screws and everything works fine

My baking element went out in my over, it started on fire.

  • Customer: lori from Vermillion, SD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
Very quick and easy fix. Used a nut driver to unscrew the bolts. Pulled it out and disconnected the two wires. I was very happy with the wonderful service we received from Partselect.com. I ordered the part Sunday evening and the part was here Tuesday by noon. I payed regular shipping charges. What a pleasant surprise!

Bake element burned into while baking

  • Customer: Marcus from Gastonia, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 1 of 1 people found this instruction helpful
Take out 2 screws disconnect the wires one on each side removed element recoonnected the wires put the 2 screws back in . Also I did flip breaker off while working. When I turned the oven on I noticed it gets bright red almost instantly. I dont remember my old getting red at all. this tells me it probably needed changing a lot earlier. I ordered the part sunday nite it arrived wednesday at lunch.I will definetly use this co again.

Bake Element quit heating

  • Customer: Robynn from St. Louis Park, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
Unplug the oven, open the door, take the screws out of the back wall that hold the small brackets which hold the element. Pull the element out of the wall, and pull a little of the wires with it to grasp easily. There are square nut screws, so you need the appropriate tool. Unplug the old element from the wires, and plug the new one in. Screw everything back together! This was a very easy fix!

Oven element burnt in several places

  • Customer: Larry from Cowgill, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
Just followed the same instructions that the other people did when replacing this element. Was very easy to replace . Just turned off the power , rwemoved the two nuts , pulled the wires out about 3 inches and unpluged old one and pluged in the new one, replaced the nuts and volia ,DONE

Oven element broke in three!

  • Customer: Keri from Raleigh, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
First I gave my roommate (an engineer) a screwdriver to remove the two screws that held the element in place. Then before I could hit the switch for the circuit breaker, he nearly fried himself by trying to take out the element! He gave up helping me after that.

Then I turned off the circuit, pulled the oven out and unplugged it, removed the racks from the oven, removed the two screws that hold in the element, and lifted up each side of the element and pulled each piece out. Unfortunately, they were a little stuck in back.

So I pulled out the oven, unscrewed the 6 or 8 screws that held up the back panel, and pulled the back panel off. I disconnected the two wires clipped to the element and pulled the old element out by lifting up and pulling them out. I then put in the new bake element, clipped the wires back on, put the oven's back panel on and screwed it in place, and then screwed the bake element back in with those two screws. Easy - a

Heat element burned out.

  • Customer: Laura from Hurricane, UT
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 1 of 1 people found this instruction helpful
The problem I ran into Was; Having the right socket size for doing the project. After taking care of that problem it was fairly easily to disconnect the element and reconnect the new one. It's pretty self explanitory.

Didn't Bake

  • Customer: Dale from Athens, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
Took it off, ordered a new part and put it back on.
Ordered on Monday and got the part on Tuesday.

Oven wouldn't heat

  • Customer: KaShira from Wilmington, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
My husband removed the screws and took out the heat element and when we received the new heat element in 3 days (thank God!) My husband put the new part in the oven and replaced the screws!! Total repair time was about 5 mins!!!

Banking Element needed replacement

  • Customer: Mitchell from Sebring, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 1 of 1 people found this instruction helpful
For an electrical appliance, it doesn't get easier then this, this was real easy.

I removed both baking racks, unscrewed two screws holding the old element in place, pulled out element about 1 1/2 inches, removed the wires off of each end of the element, then replaced with new element in reverse order. That was it. Had time to play 18 holes of Golf!

oven not heating

  • Customer: janet*hubbard from Old Town, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
slid the old one out and slid the new one in.turned the unit on and it works
All Instructions for the TEF351EWC
91-105 of 516