SRD22S5E Amana Refrigerator - Instructions

I used board levers to do one side at a time.Kinda tricky, but you can hoist up fridge high enough to replace wheels. take your time think it out and be safe . Make sure you use saftey boards to support load to protect yourself==good luck A small mirror may help to see how the rollers alien in the supports.

I determined that the ice maker was not getting any water. There was only one possibilty, the water inlet assembly. I removed the cover on the bottom back side of the fridge, then removed two screws, three water connections by hand, two electrical connections, reversed everything that I had previously done and in about twenty minutes the ice maker had water.

I removed the plastic cover from the top hinge and loosened the screws. The magnet seal kept the door in place so I removed the top hinge and tried to lift the door off the bottom hinge but the water line wouldn't let it go. Since I don't use the water feature, I just cut the water line and lifted the door off. That's when I discovered the hinge pin was actually broken off, not just the cam. I went ahead and replaced the cam kit and put it temporarily back together, got right back on line and ordered the bottom hinge. The service was again very fast and in a couple of days I received the bottom hinge, repeated the whole process again and this time replaced the bottom hinge assembly, put some petrolium jelly on the cam kit and now it works smooth and perfect.

First I removed the knobs, then the plastic cover over the thermostat. Then, I removed the two screws that hold it on. I removed the thermostat, unplugged the electrical leads, and pulled out the old thermostat. I then inserted the new one, hooked up the leads and reassembled.

I pulled the whole unit(condenser&overload relay)
with my hand & disconnected the wire connected
to it & Replaced it with the new one.Peace of cake.

Took longer to move food from door to inside fridge & take grandkids' artwork off door, & then put it all back than it did to replace cam.
1. Used phillips head to undo 1 screw holding cover over top bracket; lifted off cover.
2. No need to have someone hold door while you remove top bracket; magnets in door gasket will hold it tight to fridge. Used socket to remove 3 screws in top bracket & lifted bracket up off top of door.
3. Door's not heavy. I stood on a sturdy chair to get better leverage. Opened the door enough to break the magnetic seal & llfted it up off bottom bracket. I moved it over just enough to get to the cam, rested the bottom of the door on the floor, & leaned it up against the open front of the fridge to help preserve chilled food.
4. Removed the 1 screw holding in the bad cam to the bottom bracket (uses smaller socket than screws on top bracket).
5. I checked part that goes up inside bottom of door & it was fine, so did not replace it.
6. Trickiest part: putting the door back on. I put a hand mirror on floor by the right corner & facing up so I could see the underpart of the door as I lifted it eased it down on the right place.
7. Closed door, made sure it was straight, replaced top hinge & cover, food, & artwork.

Unplugged refrigerator. Used nut driver to remove small bolt retaining wire cover on right side of ice maker. Removed wire cover, used flat head screw driver to depress side-rail clips. Ice maker slid out, unplugged. Timer module cover pops off easily. Three screws removed the timer module. Installation was reverse of removal. Had ice in less than an hour, bin was full by next morning. If you have a screw driver and know what it's for, this job should come easily.

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

Snapped the large end of the coupling onto the main line coming from the water source and snapped the other end onto the small line leading to the ice maker. Quick and simple.

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!

The old icemaker had a bad motor and would stall in the fill cycle causing my kitchen to flood on occasion.

The new one was so quiet, I thought it didn't work!

Anyway, one nutdriver and 5 minutes and I had the new one in there... It is so quiet, and I always have plenty of ice now!!!

Thanks!!!

Unplugged refrigerator. Removed lower back access panels and panel running up the back of refrigerator. Removed and disconnected old fan. Removed old fan motor from mounting bracket. Removed fan blade from old fan motor and placed on new fan motor. Connected new fan motor to power supply. Tested. Reinstalled.

removed screws that held the ice maker in place, then removed the cover (popped off) The drive element was easy to remove, three screws and it was out. I put in the new part and reinstalled the icemaker with the three screws that hold it in place. I never call Sears for any repair. They use contract help and I have heard horror stories about those guys!

Refrigerator was stored for about 2 years and we picked it up when the owner decided to move into an apartment and no longer needed to unit (lost home to foreclosure). Brought the unit home and it worked great for about 3 days. On the third day my wife noticed a slight electrical burning smell. I did also and quickly emptied the unit and hoped for the best. The unit did indeed stop working. I fancy myself a do it myselfer but I would normally not go near electricity but thought what the heck it was free if i ruin it I would give it away. After a little research i found Partselect and they had a great design and a few stories that sounded similar so i pulled the relay capacitor for the compressor and sure enough the unit showed burn marks where the unit had shorted out. Maybe a bug got in there or water, dirt but I ordered the part. I arrived in two days which was great. I installed the part and plug the unit in and crossed my fingers. Very happily the unit clicked on and has been running great ever since. thanks Partselect, while I may not be one of your big customers I will refer anyone with appliance issues to your site first.

ridiculous how a tiny plastic broken part required a full motor assembly replacement. that being said, i went online, found this website and easily identified the part i needed to order. i was impressed when it arrived within a couple of days. removing the old motor and replacing the new was a piece of cake...and i am NOT mechanically inclined,