SG9900 Maytag Washer Dryer Combo - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer Not Draining For Spin Cycle
First checked for clogs or loose/broken belt. Fixed loose belt and tested, not the problem. I then ordered the pump and hose that would not seal after uninstalling. Everything working fine. Very simple repair.
Parts Used:
-
GERALD L from DENHAM SPRINGS, LA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
lint filter torn
-
Larry from Mount Vernon, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
replaced the worn tumbler belt
In addition to removing front of dryer, had to ultimately remove the access plate at rear of machine to thread the belt. Found aligning the belt to be a bit of a chore as the belt wanted to ride in the groove on the drum which didn't align with the motor pulley. Didn't have the correct wrench for the four sheet metal screws that held the rear plate and had to use pliers. Patience finally paid off and the machine is back in action.
Parts Used:
-
Thomas from Malone, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
tub support pulley worn out
followed directions from the video, helped very much
Parts Used:
-
Scott from Waterford, CT
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
No flame
when I see its no gas flame, i deduct the flame sensor and the electric coils not fuction, I order tru partselect and that take me like 30 min. to remplaced those parts.
Parts Used:
-
Rafael from SAINT PAUL, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
leaking from tub
I watched the online video that was supplied when I ordered the part and it made all the difference in a successful repair. Thank you for having such a complete solution!
Parts Used:
-
John from Dedham, MA
-
Difficulty Level:Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
very squeaky dryer under load
My take apart, fix-it son, Had it all apart and fixed in under 2 hrs. Thanks for quick delivery.
Parts Used:
-
Dianne from Pembroke, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
Was this instruction helpful to you?
Thank you for voting!
A water leak during the wash cycle
I watched the video and it was just a easy as the video stated. This part was stated as a common problem causing the water leak. I was doubtful after looking at the old part because there were no visible signs of wear, but decided to go along with the guidance and sure enough, it fixed the leak. It was a minor cost and an easy fix.
Parts Used:
-
Anne from Shelburne Falls, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Siphon Break leaked on spin cycle.
Remove front cover lower screws(2) with Phillips screwdriver. Remove Upperlid Bolts (left & right side) under top cover , Flip lid Back to access siphon break (rear right corner) Remove drain hose clamp, Remove clamp at bottom of siphon break. Remove (4) screws rear of washer around drain hose elbow. Remove siphon break, reinstall in reverse order. (Make Sure new siphon break washer is installed in siphon break.
Parts Used:
-
Phil from Portland, OR
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
No agiation on wash cycle
Remove screw on lower side of agiator, pullout agiator. Remove top washer clip and washer. Remove damaged seal and broken seal spring. Clean out debree and soak drum seal housing with WD40.Make sure shart will turn, iastall new spring seal and agiator.
Parts Used:
-
Phil from Portland, OR
-
Difficulty Level:Easy
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!