Models > SF368LEPS0 > Instructions

SF368LEPS0 Whirlpool Range - Instructions

All installation instructions for SF368LEPS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SF368LEPS0
16-30 of 127
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven and Broiler Wouldn't Light

  • Customer: Steven from Las Vegas NV
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 6 of 6 people found this instruction helpful
#1) Pulled the range away from the wall and unplugged the electrical cord
#2) Turned the gas valve off and pulled the range away from the wall as far as the gas line allowed.
#3) Disconnected the gas line at the range and pulled the range out to access the regulator at the bottom and pulled out the bottom shelf to access the front of the regulator.
#4) I took photos of the regulator front and back for future reference.
#5) Unhooked the feeder gas lines to the oven and cooktop in the rear.
#6) Unhooked the three electrical wires attached to the regulator front and removed the set screw at the air/gas shield feeding the oven distributor and slid the shield down to the feeder line seat.
#7) Removed the four set screws holding the regulator to the back frame.
#8) Installed the new regulator with the four set screws in the back. Applied thread dope to the two gas feeder lines and installed the gas lines to the new regulator.
#9) Referenced the photos taken earlier for proper electrical colored wires to the regulator terminal block and reset the air/gas shield in the prior location and tightened the set screw.
#10) Applied thread dope to the main gas line and installed it in the supply side of the regulator. Turned on the gas and sprayed soapy water on the threads (all) to check for leaks.
#11) While the range was still away from the wall, plugged in the electrical cord, set the time, turned on the oven and broiler to checl operation.
#12) Cleaned up the range back and floor and moved it back into place. Re-leveled the range and received accolades from my Wife for a job well done. (perhaps now she will actually cook on it)

the part that fits on the stem to turn the knob had broken. I tried to tape it together, but that did not work.

  • Customer: Charlaine from Romeoville IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
since it was the control knob, all I had to do was to push it right onto the stem, and it was finished. Using the web site to find the correct item was very easy.

Inside brass liner in socket came out when bulb was removed. Apparently had welded itself to the base of the bulb

  • Customer: Lewis from Chapin SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 7 people found this instruction helpful
Removed oven from wall unit and took the back off. Removed the old socket assembly by depressing the ears and forcing unit into the oven. The electrical wires were easily removed since they are spade connections and slip off. They also are different sizes so that there is no chance of erroneously putting them back in an incorrect order. The new unit simply slips in from the front and snaps into place. The most difficult part of the entire process is removing the old unit. A little "friendly persuasion" is required to get the old unit out.

Gas regulator started to leak.

  • Customer: Jason from Apple Valley CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 6 of 8 people found this instruction helpful
First I removed the gas line from th wall. Second I removed to gas lines going from the regulator to the stove. The regulator then unscrewed from the stove itself and that was it. I reversed the process to install the regulator.

Original handle snapped off.

  • Customer: Edmund F from Sewell NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Removed the two screws holding the remaining pieces of the old handle - screwed in the new handle.

Oven light not working

  • Customer: Carol from Allison Park PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 7 of 12 people found this instruction helpful
I turned off the breaker (I'm a little nervous even unplugging a 220 plug). I first removed the cover from the back of the stove to get to the wiring/socket. Removed the two wires from the leads - they just pull off by hand but use a needlenose pilers if it is stuck. One is larger so no need to try to remember which one goes where. I removed the glass cover and bulb from inside the oven. I read another post on this site that said there were clips that you had to press to get the old socket out which helped. That part was a little tricky as the insulation around the socket makes it hard to see and the opening is really tight. I finally found the clips and pressed one then got that side out enough to hold the clip back then pressed the other clip and I was able to push it right out. I did not have the strength to press both clips with enough pressure but if you do, that would probably be easier. From inside the oven, I pushed the new socket through the hole - there was a little notch in the opening that had to match up with the socket. I had to push pretty firmly until I felt both clips snap in place. Replaced the wires, turned on the power, screwed in the bulb and cover and I had light!

oven would light and a few seconds later go out. broiler and cooktop still worked.

  • Customer: James from Millbury OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 20 of 51 people found this instruction helpful
A very easy repair, just wished it would have worked. The diagnostic flow chart first recommended changing the igniter. The direct spark ignition board (DSI) checked out OK with a multi meter but now the flow chart recommends I change it. Wish somebody at Sears or Whirlpool ( they made the stove for Kenmore ) knew how to diagnose their own machines.

dropped stove forward, handle broke and trim around it also broke.

  • Customer: HERLIN from BOERNE TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Unsrewed what was left of the trim and oven handle. Just 4 screws total, then replaced the 2 screws of the trim and the 2 screws on handle.
Finished! Replacement parts fit perfect!!! Thanks a milliion!

The gas Safety Valve leaked gas.

  • Customer: DAVID from ALBUQUERQUE NM
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 4 of 4 people found this instruction helpful
This is a very simple repair. 1st shut off your gas. Disconnect your gas line from the gas shut off value to the Gas Safety Value(GSV/R)/Regulator. Disconnect the other 2 lines attached to the GSV/R. Remove the 4 mounting screws holding the GSV/V. Wiggle the GSV/R from its location. Carefully remove the 3 wires connected to the GSV/R. Install your new GSV/R in reverse order applying sealant to the threaded joints. test for leaks.............. your done!!!

broken handel and trim

  • Customer: James C. from Middletown OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 10 people found this instruction helpful
Un-screwed 4 screws. Got part numbers off of the pieces. Put numbers in blank on web site and ordered the pieces. Parts cam in 4 days later and installed the pieces with my trusty screwdriver.

scratches and paint detoriation on bottom part of oven

  • Customer: Peter from Galloway NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
Remove 2 screws holding oven bottom in place.Lift out the plate and replace with new plate. The hardest part of the replacement was lining up the screw holes. By the way i have never received such great service from any internet company as Part Select. I ordered the part on a Monday and the part was at my home the NEXT DAY and installed that evening.

Glass broken on outside oven door

  • Customer: Quail Valley from Clive IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 16 people found this instruction helpful
Checked to see that I had all the parts I needed.
Installed bottom door trim then side trim pieces.
Do not tighten screws. Install door handle with top
trim attached over glass. Tighten screws just snug
all around.

missing screws for oven door

  • Customer: donna from baltimore MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

Oven stuck in cleaning mode

  • Customer: Hal from Santa Rosa CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 17 of 44 people found this instruction helpful
Google the error code that the range was displaying and found others with the same symptoms. Then found several people that had fixed the problem by replacing the oven sensor. I then ordered the sensor and replaced it, which fixed the problem.

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 5 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
All Instructions for the SF368LEPS0
16-30 of 127