Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SF368LEPS0 > Instructions

SF368LEPS0 Whirlpool Range - Instructions

All installation instructions for SF368LEPS0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SF368LEPS0
31-45 of 131
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

scratches and paint detoriation on bottom part of oven

  • Customer: Peter from Galloway, NJ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
Remove 2 screws holding oven bottom in place.Lift out the plate and replace with new plate. The hardest part of the replacement was lining up the screw holes. By the way i have never received such great service from any internet company as Part Select. I ordered the part on a Monday and the part was at my home the NEXT DAY and installed that evening.

Bottom door trim was rusted

  • Customer: Timothy from Terre Haute, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
Removed oven door and the 3 screws holding the bottom door trim. Attached new trim piece and reinstalled oven door. Entire job took less than 5 minutes.

dropped stove forward, handle broke and trim around it also broke.

  • Customer: HERLIN from BOERNE, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Unsrewed what was left of the trim and oven handle. Just 4 screws total, then replaced the 2 screws of the trim and the 2 screws on handle.
Finished! Replacement parts fit perfect!!! Thanks a milliion!

Door bottom trim piece was rusty

  • Customer: Dennis from Dunnellon, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
Remove three screws, slid old trim piece off door. Slid new trim in place. Used ice pick to align screw holes and replaced screws. Total time about 15 minutes. Tip: used a bead of silicone sealer on the new trim strip to prevent moisture from causing new strip to rust.

Lower Door Trim gets rusty

  • Customer: James.O from Newark, DE
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
I have removed this piece once before and painted it,
but it is difficult to prepare surface.

I tried to replace the part without removing the door
but had difficulty getting the screws to line up.

So, I took the door off. Forgot that you are supposed to jam
the spring hinges in the open position before you remove the door. Manual describes how to do this but picture is not very helpful. So I made two wooden dowels about 3/8" in dia by about 3/4" long. Opened the hinge with a screwdriver and jammed the dowels in place.

Door Trim went on easily and the oven door went back on quickly.

Surprised they don't make this trim piece with rust proof material.

I just intalled the part, but the problem continued

  • Customer: Wagner from Miami, FL
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 10 people found this instruction helpful
I had problem with the oven of the stove since the beginning. It wa difficult to start. Later, it stoped working. The technician told m that the gas valve regulator was the problem. That was the reason I decided to buy a new one. After installing it, however, the problem continues. The ignition starts, but the gas does not go thru. It seems the signal does not go to the valve to open the gas.

Broke glass door on stove while cleaning it

  • Customer: Aires from Canton, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 19 people found this instruction helpful
I'm still unsure why it broke ,but it was just a matter of removing two screws that hold the handle in place and sliding in the glass...

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell, WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 5 of 7 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Over would not heat

  • Customer: Jeffrey L from Otterbein, IN
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 5 of 7 people found this instruction helpful
On the back of the range was a little plastic bag with the range document. In this document was instructions on how to check out the electronic controls, a drawing of the electrical wiring and a digram of the gas line part of the range. First I did the electronic part and it check fine. Following that the instruction was to check out the solenoid coils for the bake and broil valve. I believe the wires were blue, red and orange(it tells on the wiring diagram). It called for 216 ohms on each coil. When I unpluged the plug from the circuit board on the upper right backside of control panel I checked the resistance for the two coils. One side had 198 ohms and the other coil had 0 ohms. The instruction said that if either coil didn't measure 216 ohms or close to that value the valve would not work. So, I wrote down the Model number. Next I checked the gas valve for numbers, wrote down all that was on the valve because I didn't know which one was the part number for the valve. Went on line to the Whirlpool site, once in the Whirlpool site I found out they have a diagram of parts for different appliances, pulled up the model I was looking for, found the valve( under the valve part, the number was different than the one I had, but the information said it would fit the model of appliance I have) order the part. In a few days the part arrived. I turn the gas off, unplugged the electric. I removed the gas lines, had just a bit of a problem with the short gas line going to the burner for the oven, when the line was out I unplugged the control wires. Nake sure you write down how thw wires are on the valve before unplugging. There is an adaptor on the valve to the main gas line. You need to take this off and put on the new valve. This is where you need the pipe cement. Stay back from the end of the adaptor that goes into the valve one or two threads with the pipe cement. you do not want to get any inside of the valve. Put the adaptor on, tighten, plug in the control wires, replace the valve on the stove, connect the gas lines, put all the gas lines on before you tighten them. Turn on the gas. Check lines with soapy water for gas leaks. Plug in the electric, check it out. Don't forget to put the instruction back in their little plastic package and I also put a copy of the order I had for the new valve just in case I need it in the furture.

center hold of kn ob cracked

  • Customer: Mary Ann from Carteret, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Took knob off ordered new one put it in place

The Gas Safety Valve would not shut off. Gas conyinued to flow when oven switch was turned off.

  • Customer: John from Hardwick, VT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench (Adjustable), Wrench set
  • 4 of 5 people found this instruction helpful
Removed two gas lines at the safety valve. Removed the four mounting screws and disconnected the three wires. Re-assembled in reverse order of dis-assembly. This was an easy diagnosis and repair/replacement. The PartSelect website is very easy to use if you have the model number and I like the diagrams to be sure the part is correct.

Outer glass of the oven door is broken.

  • Customer: Ernestine from baltimore, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 15 people found this instruction helpful
I took out the two screws that held the oven handle in place inserted the glass in the door and replaced the two screw!!! That easy!

Oven light would not work--faulty socket

  • Customer: Delores from Warren, MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 6 people found this instruction helpful
After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

Oven bottom heavily corroded; difficult to clean.

  • Customer: Edward from Sinks Grove, WV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Removed two screws holding the bottom in, pulled out old bottom, inserted new bottom, replaced screws and tightened them. Total time less than five minutes.

broken bottom drawer glide and missing rivet on drawer front panel

  • Customer: David from Fairborn, OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Removed the old, broken drawer glide by removing the Phillips head screw. Then placed the new glide into place and fastened with the existing screw.

The rivet on the top of the bottom drawer front was missing. I lined up the drawer front with the supporting bracket behind it and inserted the rivet. All you have to do is tap the top of the pin in the center of the rivet to lock it in place. No rivet tool is needed. That should be explained in the parts listing because I bought the rivet tool before I realized I didn't need it.
All Instructions for the SF368LEPS0
31-45 of 131