Models > SEG196 Maytag > Instructions

SEG196 Jenn-Air Range - Instructions

All installation instructions for SEG196 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SEG196
106-120 of 130
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Worn out burner grates

  • Customer: Richard from Omaha NE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Lift and replace. This was the only web site that gave a picture with the correct size of the grates I was looking for. All the other sites gave approximate sizes and universal part numbers instead of the vendor part number. That is why I bought it here. I didn't want to have to return the product because it was off just a bit.

Bake element burned out

  • Customer: Bryan from Rougemont NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
undid the 2 screws inside the oven holding the element in place. slowly pulled the element out to get to the wire on the end. unplugged the old element and pluged the new element in and slowly slid wires and element into back of oven. secured with the 2 screws and turned on to check operation.

Burners would not light - rusted

  • Customer: Bob from Mansfield TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
New front burners fit well, but back ones had just enough variance in tne angle of the gas-supply tube that it would not fit the mounting bracket holding both burners in place. I had to grind a small flange off of the bracket so the gas tube would clear. Once that was done the burners worked well.

Oven Selector Knob broke after 20+ years!

  • Customer: James Edward from Gardnerville NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Old (broken) knob was gone, so wife oriented new knob over selector shaft, and pushed onto shaft!! PROBLEM FIXED!!!!! No fuss, no mess - just as good as new!

Wanted to replace old grease filter

  • Customer: Christine from Pembroke VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed old filter, dropped in new filter. A breeze! What was best of all, is that Parts Select shipped the filter immediately and it arrived within just a day or so! Well done!

Old burners

  • Customer: Alan from Scappoose OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The issue: the burners were abused by the previous tenant, the burnt grease was clearly visible. They would hardly ignite and the smell of gas was always present.The remedy: new burners. They were hard to find, I was not completely sure about to stove model (it could be quite a search to find the right ones). There is a front burner and a back one. I was not sure from the diagram about the back one, so I called Partselect and someone answered the call right-away. The burners arrived a few days later, and they were the correct ones. The burners are not Jenn-air specific, it looks like several brand names use the same ones. The installation was extremely easy, a few hex screws. The stove is like new. I highly recommend Partselect.

broken interior window

  • Customer: Kay from Hot Spings AR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Decided since the glass was broken I might as well replace the door seal. Getting the door off and on was the most difficult part of the process as the door hinge springs are quite strong. Remove screws on the hinge. Slide door off hinges. The hinges will close rather hard. Remove screws along the outside, then inside. Keep all the screws in some order as they are different sizes. More time to clean the door than actually installing the glass and seal. Re assemble. Trick to getting the door back on is to open the hinge spring to the broil position and place a thin screwdriver in an opening in each to keep in an open position. Slide door down to the srewdriver stop and then fully open. You can then slide the door fully onto the hinge, replace the hinge screws. Easy ,for a simple housewife.

Filter was old and discolored.

  • Customer: Robert from Warroad MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The new replacement grease filter came without damage and it was a simple task of removing the old and setting the new in it's place. No tools were required.

only one burner on the cooktop worked

  • Customer: William from Chipley FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took two screws out of each burner and put new burners in and replaced the screws. A real piece of cake. and they work great. Did not even have to adjust the flames. They were all solid blue and perfect. Bill

Burner was not lighting

  • Customer: Luciano from Hollister CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed the pan and then the burner assembly. Used a nutdriver to remove the old front burner. Replaced with the new part, tightened it on, and tested the new burner. Worked first time. Extremely easy. It took less than 5 minutes to replace.

Light burned out in upper oven

  • Customer: Shirley from Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Screwed in light bulb and glass protector

range seal worn and leaking

  • Customer: Camilla O from Sanford NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed front of range door. removed old seal and replaced with new seal. clean and reassemble range door. repair very simple and fast.

Needed a new oven door seal

  • Customer: Mary from Apple Valley CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Left door attached to range. Took out all screws on door to get to the door seal. Cleaned parts as I went. Took out old seal and laid new seal in. Had to get two more hands to hold the parts and glass together while screwing it back together. Only hard part was remembering which screws went where. Looks and works like new. So glad I did it, as it has needed it for a long time. Easy even for a 70 year old female. PartSelect had the best price even with shipping. Thanks

needed to replace the grease filter

  • Customer: Nancy from laveen AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I lifted the grill off; took the old grease filter out and threw it away; placed the new filter in the well; put the grill back on. Wallah!!! just like new.

light bulb socket broken

  • Customer: Blanche from Woonsocket RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed glass and then two screws to remove metal plate pulled out socket,disconnected two wires and installed new socket.
All Instructions for the SEG196
106-120 of 130