Models > SEG196 Maytag > Instructions

SEG196 Jenn-Air Range - Instructions

All installation instructions for SEG196 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the SEG196
76-90 of 134
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Filter Worn Out

  • Customer: Thomas from Berlin, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 4 people found this instruction helpful
Remove cover and install

50 year old oven racks in bad shape

  • Customer: GREG from PETALUMA, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Parts no longer available so we went to several appliance stores and measured racks. We found a jenair model had racks that measured correctly got the model number and ordered the racks. There working great and now the oven looks like new. Our kitchen is a restored 1956 GE metal kitchen in Cadilac pink. Thanks guys for the fast service and very resonsble price. Was also very happy to find the racks were made in USA.

Burner wouldn't light.

  • Customer: Clark from Tifton, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
Took out a couple of screws and put in the new part. PartSelect was fast and efficient. Highly recommended.

simple swapping of parts

  • Customer: lenny from east freetown, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
Undid the bad part and installed the new one

replaced the current warn-out grease filter

  • Customer: Joseph from East Greenwich, RI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
removed the old by pulling it out of track and replaced it with the new filter

Burnner rusty and will not start with electric start.

  • Customer: Robert from Mary Esther, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 2 people found this instruction helpful
Removed and installed burners in less than 15 min with just a nut driver. Replacing the burn ere did not fix the starting problem, but replacing them did improve the hurried flame.

the original grease filter was worn and falling apart

  • Customer: Barbara from Medfield, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
Removed the old filter from the top of stove and put the new one in. Took about 10 seconds.

Blower motor had frozen up.

  • Customer: Joe from Fair Oaks Ranch, TX
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 3 people found this instruction helpful
Removed front wooden kick panel(2 cross recessed screws).
Removed 2 bolts holding blower to floor. Loosened 2 vent clamp screws on vent from stove(2 clamps). Pulled vent off of blower housing. Removed blower from under stove. Using a nut driver, removed 4 nuts from blower and removed the motor cover & motor from the blower housing, removed 3 screws from motor cover and removed the motor cover from the motor. Ordered new motor. After new motor was rcvd (about 3 days plus wk end) I removed the squirel cage from the motor shaft using a metric allen wrench. Then removed the mounting clamp from the old motor by loosening 1 screw. Placed the motor clamp and the squirel cage on the new motor, then placed the motor cover on the motor. Placed blower mtg bkt and motor on blower housing w/ the 4 nuts removed earlier. Placed blower motor assy under stove being careful not to damage the exaust vent behind the blower motor as I carefully put the blower motor into the exhaust vent. Placed vent from stove on stove and blower housing and secured w/the 2 vent clamps removed earlier. Attached the blower motor base to the floor w/ 2 bolts. Wala........complete

burners were corroded and wouldn't fire

  • Customer: Russell from Natick, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 3 people found this instruction helpful
I removed the old burners from the stove top. I then removed the screws holding the two burnes on to the mounting plate. Used WD-40 to loosen them up.
I removed the old burners and put the new ones onto he plate then re-installed the burners on to the stove..............a cinch. Easy as pie, piece of cake.
Thanks!

The filter in the grill section of my stove fell apart.

  • Customer: Beth from Dunkirk, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
I simply removed the old filter and replaced it w/the new filter. It came in record time and I'm very pleased w/the service I received.

Drain Tube Nut was missing from day 1

  • Customer: Joe from Ridgefield, CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 3 people found this instruction helpful
Hours to reveal the issue. Many more hours of cleaning grease. Not real happy with Jenn-Air quality control.

I Destroyed My Grease Filter In The Dishwasher And It Just About Disintergrated.

  • Customer: Rosetta R. from Jamaica Plain, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 6 people found this instruction helpful
I just had to drop the grease filter into the slot. It took less than a second. But what I am really pleased with is that it took less than a day and a half to get the part. I ordered it on thursday morning. It was shipped on thursday afternoon and in my driveway by friday noon!!! Wow!!! How great was that!!!!!! The fastest service I've every had for anything!! Bravo!!!!!!!! To all your workers!!!!! Rrm

range handle fell off and screw got lost

  • Customer: Frances from palm beach gardens, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 3 people found this instruction helpful
It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.

Salve money

  • Customer: Okey from Jacksboro, TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench (Adjustable)
  • 0 of 4 people found this instruction helpful
installed parts

Broken knob

  • Customer: Raymond from Casselberry, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 6 people found this instruction helpful
Replaced the knob.
All Instructions for the SEG196
76-90 of 134