SCE30600BC Jenn-Air Range - Instructions

Followed provided video

1. I removed the 4 Philip head screws that hold the trim plate on the bottom of the display panel and also removed the knobs from the display panel. 2. Then I removed the 4 hex screws from the bottom of the front panel 3. Remove the display panel and expose the Electronic clock. 4. Remove the two hex screws hold the clock. Moved the clock, then remove the three connections to the clock. 5 Attach the connections to the new clock and reassemble everything in reverse. Take about 20-30 minutes. Not a difficult job.

I removed the old sensor via the two screws holding it in, unplugged it and replaced it with a new one.

Unscrewed three screws securing the glass top. Lifted glass top and wedged it open. Took a picture of the current wiring. Removed old burner.Compared male contact points on new and old burner. Plugged new burner in appropriately. Note: The new burner is MUCH hotter than the old one.

Turned of the power, removed an old element, by unscrewing 2 screws, pulled out element out about 4 inches, remove the slide on connectors, then put them back on that new element, carefully slide in element to the back wall and screw in the 2 screws. Turn the power back on. It is nothing to it. When the old element is out, I took an advantage and cleaned up the inside, using the oven cleaner sprayer.

The thermocouple was suspect. It should be super easy- two screws, but the wiring harness would not pull through on my oven. I confirmed the procedure with the PartSelect video which is good. The harness was caught and broke so I had to pull the oven out partially to get to the harness. The sensor did check bad on the multimeter (resistance too high- Google it, I did) so I ordered the part. Once the new part was installed the oven still did not function. So I had to get busy with the multimeter and pull the oven again. On the back of my oven near the wire to the bake element is a Hi Limit Switch which cuts off the bake element if the outside of the oven gets above the preset temperature. Mine was cracked and faulty and had to be replaced. The oven works great now.

Thanks to the highest rated user comment and following his instructions the switch exchange was easy. The supplied instructions were of little to no help and confusing. The hardest part was getting to the two side top Phillips screws because the granite counter top was in the way necessitating raising the stove till the screw heads were exposed. Once raised the front cover was easily removed after undoing six screws. The cook top did not need to be removed. Either of the supplied wires would work and only one of the two was needed. The replacement switch performed far better than the original.

Remove 2 screws in upper left corner of stove holding sensor in place. Pull sensor out and disconnect plastic electrical connector. Select appropriate adapter (both styles provided with new part) & reinstall. Power up stove and select bake on control unit to test. Works like a charm!

I never reply to these surveys, but this was so brain dead simple, I had to respond. You take off two safety screws ( the ones that keep the oven door from falling off) You take off 6 screws holding the door together in order to remove the old hinges, put in the new hinges, put the six screws back in that hold the door together, put the oven door back on. Oh, and then put the two safety screws back in the so the oven door does not fall off. The only advice I have is put a big beach towel down to keep anything from getting scratched. Very Easy and saved me a lot of money.

Lifted the range top about 2 1/2 inches, removed the ceramic top and replaced the burner. Tested the burner before replacing the top. Everything worked fine.

I removed the old thermostat and replaced it with the new one using the supplied wiring adapter for my model of range. Parts Select made this an easy project. Thanksyou

Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.

STEP 1 GO TO YOUR ELECTRICAL PANEL AND SHUT OFF THE BREAKER OR REMOVE THE FUSE. A drill/driver with a phillips bit and extension is all you need. The 1/4" extension is the correct size for the hex screws. Remove them, then the phillips screws and put aside. Remove the control knobs, then the small screws behind them. Remove the trim and clean as it is most likely somewhat greasey, pull the clock board away from the range so that you can disconnect the wires. Lift the tabs holding the ribbon cable to the board and remove the cable. Now that wasn't as hard as you thought it would be was it? Now reverse the proceedure and you will have a working stove again and will have saved a $100 service call. Don't forget to reset the breaker.