S120-C Jenn-Air Range - Instructions

- the fan/light switch was still functioning, but it fell into the cavity underneath, after years of use, heat and grease caused it to weaken.
- 4 wires came off the old switch, and went on the new one with ease.
- the only complication was in getting the clips off of the old ones, and getting the new clips onto the new one. otherwise, a piece of cake.

Remove the screws from bottom of door to gain access to the hinge screws. Remove the bottom hinge screws and then open the door to gain access to the top hinge screws. CAUTION after removing the top screws close the door as far as possible while still griping the sides of the door. Pull up on the sides to remove the door from the stove. The springs are fully loaded if you have the door open all the way and try to lift up (like I did) the hinge will spring back and get your finger. Install the new hinge, put the door back into the oven, install all the screws and then remove the temporary rivet that comes installed in the new hinge.

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.

It would have been nice if basic instructions were supplied ( eg. how to remove switch panel ) but it went rather smoothly.
First killed power the electric stove.
I then removed the screws from the bottom of the panel and then pried the top of the control panel down and then out. I copied the positioning and wire colors.Removed wires from prongs, removed the two screws, replaced old switch with new one .

First I turned off the circuit breaker at the control panel to my Jenn-Air stove-top. At 220-volts, don't take any chances with electricity!

Then I removed two screws that hold the burner switch panel in place and lifted up the panel to expose the wires that are connected to all 4 of the burner switches, the exhaust fan and pilot lights that indicate if a burner is turned on.

I used a circuit tester to determine that the power was indeed off to the switches. Again, it is extremely important to respect 220-volts of electricity.

I ensured that all of the wires were already labeled the same as the terminal connections on the switch (i.e. H-1, H-2, P, etc.). If they are not, label them yourself with masking tape around each wire. Then I removed each of the wires connected to the burned out switch with a pair of needle-nose pliers.

Next I removed the two screws attaching the burner switch to the panel.

To install the new switch, repeat all of these directions in reverse, making sure to attach each labeled wire to the correct terminal on the burner switch.

Turn the circuit back on at the circuit breaker. Then test the burner switch and see if the burner heats up. Hopefully, you'll be cooking in no time...............

First we removed the two screws that hold the element in place. After pulling it from the back of the oven we did not realize that the clips that held the wires could be slipped off the 'tongues' of the element. Therefor we thought we had to cut the wires - which we did. After realizing that the clips came off, we went to the store and bought a box of new clips, stripped a small portion of the plastic on the wire to expose the wire and put it in the new clips and crimped them. Then slipped the new clips onto the new element, replaced it and put the old screws back. You wouldn't need to buy new clips (not expensive) if you know ahead that they can be removed from the old element and slipped onto the new one. We were amazed at how quickly the element arrived in the mail. Have bookmarked this sight for future repairs.

remove two screws, pull out element, diconnect two wires, toss old element,plug in wires to new element, replace two screws and viola- done

Now if you just sold faucet parts I'd be all set.

The hardest part of the repair was getting the old cruddy screws out of the old element. They were sort of "baked-in". Once we got the screws out the rest was really easy. Just inserted the element prongs & screwed the new ones in. Ordering & receiving the part was a snap...I would recommend your company to anyone. Thank you.

Removed two screws near the hinges and removed door and laid it on counter.
As we removed screws from each part of the door, we stacked the parts in the order removed. Tossed screws into a shallow pan for safekeeping.
Removed old seal and put new one in its place.
Reassembled parts in reverse order as I cleaned each one.
Put door back on the hinges and the job was done.
Would have been a much quicker job, but door had 24 years of dribbles down in it, and needed a good cleaning.

We ordered a new element also, as the old one had blown up. Very gratifying to know there were still parts for my favorite old range.

The hardest part was breaking the caulk seal between the range and the cabinet. An extra set of hands made the job easier, by holding the panel while I connected the switch. The switch was delivered promptly and I am very happy with Parts Select. I found the other repair stories very helpful.

Replace filter

Unplugged and removed the old grill element by hand and installed the replacement element by plugging it into the socket. Tools were not required for this and it took less than five minutes. The new element is great and heats much better than the original did before it broke.

After accessing the switch and removing the wires(four wires as the rocker switch operates both fan and oven light) I attached the wires to the new switch. However , I was unable to mount the switch in place as I could not get the spring - clip type of fasteners to slip on.
Fortunately, there was space to drill a hole on each side of the switch and I used brass machine screws
and nuts to hold the switch. The round-head screw
tops show on top of the stove, but at least the new switch is in place and operating.

I had a service guy come in and he told me the repair would be $550.00. I asked for a part list and did it myself. You guys saved me hundreds of dollars.

Simple plug in.