S105-C Jenn-Air Range - Instructions

The repair was very easy to perform, but the springs in the new hinge were not as strong as the old one. The door would not close all the way unless you held it closed. The hinge looked identical but spring had less tension.

Opened the oven door and locked the spring hinges in the opened position with two 10p nails. Removed the oven door. I dismantled the component parts of the door. I then removed and replaced the broken glass unit,reassembled the door, slid the door onto the hinges, tightened two screws to lock the door in place, removed the 10p nails, closed the door----- and that was it. Less than one hour. The job was accomplished using only a Phillips screwdriver.

Got a no-name tailor-it-yourself replacement switch from a San Jose, CA appliance parts store; but the switch was so cheaply made that it fell apart when I tested it.

Got a RobertShaw part from PartSelect and now the burner works perfectly.

First pulled the two screws holding the control with the switches. Then I unscrewed the nut holding the 6" burner switch and disconnected the wires on the switch and replaced the switch with the new one. Replaced the control unit in the range top and tested the repair.

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

removed 4 screws holding burner controls. removed wires off old and placed on new burner control. very pleased with quick shippig of part. two days and range was as good as new. excellent company to buy from

First I removed the two screws that held the old element in place. Then I pulled the element out about 5 inches so I could reach and pull off the wire clips from the old element. I then attached the wire clips onto the new element and pushed back the wires into the insulated area and when the back plate matched up to the screw holes, I re-inserted the screws and tighten them down. The oven works great.

Motor (Blower Motor Kit) Part Number: PS1569907
No instructions are included in the package from PartSelect. Disassembly from the main housing was relatively simple. I found that paying VERY careful attention to how the original motor was wired and mounted would pay off in correct re-assembly, conquering motor vibration and rubbing. Most of my project time was spent cleaning the rotating blade wheel from 20 years of grease build-up. On tools, I would have appreciated the inclusion, or availability as an accessory, of a long-stem correct-size allen wrench (used in removal of the fan blade wheel.) The job went well, and probably saved me $200 in service call and labor.

The oven that was in out newly purchased house was a JennAir and over 20yrs old. Worked ok, but as with any heating element, the performance wanes over time. I decided to replace the baking and broiling element...and the oven door seal while I was at it. Everything went well, it was a simply remove/replace. Then I bumped the oven door where it was leaning up against the fridge waiting to be reinstalled. Down it fell on the tile floor. SMASH! Tempered glass EVERYWHERE. Got online with PartSelect and ordered a replacement (very reasonable price). It arrived in 2 days...just like the elements. Replacement was easy. Thanks to PartSelect for having the parts in stock and delivering them in record time!

Using exploded view and previous customers' comments, I disassembled the door. It was primarily a matter of finding all the screws. I recommend taking the door off first (I didn't), but watch your fingers. The hinges have very, very strong springs and you can hurt your or your helper's fingers if you're not prepared. The hardest part was keeping all the insulation in place while your're installing the assembly. I also replaced the gasket. That takes four hands, two to hold the gasket in place and two to reinstall the window assembly. To put the door back on the hinges, I pulled them out from the door at a 45-degree angle (takes some effort), put screwdrivers through holes in the hinges, and guided (with help) the door back on.

I didn't. Don't know how to get to light bulb to change it for this specific model

I removed about 8 screws to disassemble the door to get the gasket in. This was an easy task. On the first use of the oven, it shattered one pane of the double glass door window. I think I installed it backwards since one pane is tempered glass, I believe. I installed the new window and am heating it up now - hope it doesn't break.

I removed the 4 screws that held on the front panel as well as the knob of the defective switch. With the panel free, I pulled the wire connections from the rear of the switch with needle-nose pliers. I then removed the 2 screws which secured the switch and removed it. I then reversed the process with the new switch. It could not have been easier.

I first removed power from the stove at the breaker panel. Next, I used the assembly diagrams provided by the parts select website to determine how to open up the stove panel. I opened the oven door to access the four screws holding the front panel holding the knobs. I removed the screws and was able to tilt up the front panel to allow access to the four burner switches. It was easy to swap out the wires on the old defective switch to the new replacement switches. I replaced both defective switches in 15 minutes and tiled the front panel back down into its normal position and put the four screws back into the panel to secure it. Then I turned on the breaker and did a check to see that the parts I replaced were working properly. They were and the total repair time was around 30 minutes without rushing at all.

pull oven, remove back pannel and unplug and remove high limit switch. Repair was the reverse of removal.